-
Supplier: Aleris International, Inc.
Description: Aleris is one of the leading suppliers of common alloy aluminum bare sheet made from recycled aluminum via two different methods: direct-chill and continuous-cast. The Aleris direct-chill casting facility is located in Lewisport, Kentucky, while our continuous casting mini-mills
- AA Grade: 3004
- Coil Stock: Yes
- Elongation: Over 4 %
- Features: Corrosion Resistant, Cold Finished / Rolled
-
Supplier: Arnold Magnetic Technologies
Description: Thin-rolled aluminum and aluminum alloys from Arnold Precision Thin Metals (PTM) are versatile and lightweight and are used in a variety of electrical products packaging and other applications. Aluminum is often the best solution when reduced weight, good
- Applications: Battery / Fuel Cell, Other
- Features: Wrought
- Overall Thickness: 1.00E-4 to 0.0250 inch
- Overall Width / OD: 4.25 to 17.5 inch
-
Description: no major alloying additions. These compositions are characterized by excellent corrosion resistance, high thermal and electrical conductivity, low mechanical properties and excellent workability. These alloys are non-heat treatable. The most common type is A91100 which is
- Applications: Chemical / Materials Processing, Other
- Elongation: 23 %
- Features: Corrosion Resistant, Cold Finished / Rolled
- Processing & Finish: Annealed, Hardened / Heat Treated
-
-
Supplier: Alcoa North American Rolled Products
Description: 6013 Aluminum Alloy Sheet Description Alloy 6013 is a new medium strength aerospace alloy that provides improved corrosion resistance and formability for use in aerospace applications including primary aircraft structures. Alloy 6013 is an
- Shape / Form: Sheet, Semi-finished Shape / Mill Stock
-
Supplier: Alcoa North American Rolled Products
Description: 2124 Aluminum Alloy Plate Description Alloy 2124-T851 plate was developed primarily for elevated temperature applications requiring guaranteed fracture toughness and improved short transverse properties in plate gauges over 1.0 inches (25.40 mm) thick. This plate alloy
- Shape / Form: Plate, Semi-finished Shape / Mill Stock
-
Description: DESCRIPTION 2000 series of alloys are a set of "hard alloys". The aluminum-copper alloys typically contain between 2 to 10% copper, with smaller additions of other elements. The copper provides substantial increases in strength and facilitates precipitation
- Applications: Structural, Wear Parts / Tooling, Other
- Elongation: 12 %
- Features: Cold Finished / Rolled
- Processing & Finish: Annealed, Hardened / Heat Treated
-
Description: . These alloys have excellent fatigue properties. In the T6 condition fracture toughness can be inferior to other alloys. Alloys in series can be spot welded but not fusion welded. If corrosion is a concern, these alloys should be anodized, primed, painted or
- Applications: Other
- Features: Cold Finished / Rolled
- Processing & Finish: Annealed, Hardened / Heat Treated
- Shape / Form: Wire / Shaped Wire, Other, Semi-finished Shape / Mill Stock
-
Supplier: Belmont Metals, Inc.
Description: . These properties allow Aluminum and its alloys to find applications across a broad spectrum of uses. Aluminum is rarely used in its pure, unalloyed state. The most common metals alloyed with Aluminum are Silicon, Magnesium, Copper, Zinc, Nickel, Manganese
- Features: Corrosion Resistant
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
- Shape / Form: Ingot
- Standards / Specifications: AA / IADS, Casting Grade (ICI, etc.)
-
Supplier: Alcoa North American Rolled Products
Description: QC-10® Aluminum Mold Alloy QC-10® Mold Plate and Forged Block Specifically designed for production injection molds, QC-10 offers greater strength, stability, and durability than any other 7000 series aluminum mold alloy on the market. Its improved alloy composition
- Shape / Form: Plate, Semi-finished Shape / Mill Stock
-
Supplier: Aleris International, Inc.
Description: Aleris is one of the leading suppliers of common alloy aluminum bare sheet made from recycled aluminum via two different methods: direct-chill and continuous-cast. The Aleris direct-chill casting facility is located in Lewisport, Kentucky, while our continuous casting mini-mills
- AA Grade: 3004
- Coil Stock: Yes
- Features: Corrosion Resistant, Cold Finished / Rolled
- Overall Thickness: 0.1250 to 0.3130 inch
-
Description: series Aluminum alloys are Aluminum alloyed with manganese. They have higher strength than pure aluminum while maintaining good formability and corrosion resistance. These alloys are not heat treatable and are suitable for anodizing and welding. Alloy
- Alloy: Yes
- Applications: Automotive / Vehicular, Chemical / Materials Processing, Other
- Features: Corrosion Resistant, Cold Work (Die / Mold)
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
-
Supplier: Belmont Metals, Inc.
Description: White Metals Featuring Aluminum, Lead, Pewter, Solders, Jewelry, Sculpture, Tin, Zinc Alloys in a variety of forms for many applications White metals are any of several light-colored alloys used as a base for plated silverware, ornaments or novelties, as well as
- Applications: Other
- Light Alloy: Yes
- Metal / Alloy Types: White / Low Melting (UNS L), Tin / Tin Alloy
- Shape / Form: Ingot
-
Supplier: Southern Stud Weld, Inc.
Description: Capacitor Discharge Studs are available in many different sizes, from a base diameter of a #2 stud up to 3/8" , and from a length of 1/4" up to 3". Standard material for CD Studs are: Low Carbon Copper Flashed Steel, Stainless Steel, Aluminum Alloy, and Brass.
- Alloy Type: Aluminum Alloy
- Approvals / Conformance: Other
- Diameter / Thickness: 0.0860 to 0.3750 inch
- Elongation: 20 %
-
Supplier: Alcoa North American Rolled Products
Description: 2090-T83 Aluminum Alloy Sheet Description Alloy 2090-T83 sheet is a fully commercialized aluminum-lithium alloy developed for high strength aerospace applications. The Al-Cu-Li alloy offers an 8 per cent density savings when compared with other
- Shape / Form: Sheet, Semi-finished Shape / Mill Stock
-
Supplier: Belmont Metals, Inc.
Description: White Metals Featuring Aluminum, Lead, Pewter, Solders, Jewelry, Sculpture, Tin, Zinc Alloys in a variety of forms for many applications White metals are any of several light-colored alloys used as a base for plated silverware, ornaments or novelties, as well as
- Applications: Other
- Light Alloy: Yes
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
- Shape / Form: Ingot
-
Supplier: Materion Corporation
Description: FormaMet by Materion Brush Performance Alloys is an aluminum bronze cold working die alloy used for the drawing or forming of stainless steel, low carbon steel and other materials. This unique aluminum bronze was specifically manufactured for industrial tooling, roll
- Applications: Wear Parts / Tooling, Other
- Features: Cast (Continuous, Centrifugal, etc.)
- Light Alloy: Yes
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
-
Supplier: Materion Corporation
Description: BrushCAST high strength casting Alloy 20C provides peak strength and hardness greater than many steels, but with thermal conductivity similar to that of aluminum, and up to five times that of steel. Additionally, beryllium Alloy 20C offers good electrical conductivity, excellent
- Applications: Aerospace / Aircraft (AQ), Wear Parts / Tooling, Other
- Features: Cast (Continuous, Centrifugal, etc.)
- Light Alloy: Yes
- Metal / Alloy Types: Copper, Brass or Bronze Alloy (UNS C), Refractory / Reactive (UNS R), Beryllium / Beryllium Alloy
-
Supplier: Materion Corporation
Description: BrushCAST high strength casting alloy 275C provides peak strength and hardness greater than most steels, and offers thermal conductivity similar to that of aluminum, and up to five times that of steel. Beryllium Alloy 275C offers excellent electrical conductivity, wear and
- Applications: Aerospace / Aircraft (AQ), Wear Parts / Tooling, Other
- Features: Cast (Continuous, Centrifugal, etc.)
- Light Alloy: Yes
- Metal / Alloy Types: Copper, Brass or Bronze Alloy (UNS C), Refractory / Reactive (UNS R), Beryllium / Beryllium Alloy
-
Supplier: Belmont Metals, Inc.
Description: White Metals Featuring Aluminum, Lead, Pewter, Solders, Jewelry, Sculpture, Tin, Zinc Alloys in a variety of forms for many applications White metals are any of several light-colored alloys used as a base for plated silverware, ornaments or novelties, as well as
- Applications: Other
- Light Alloy: Yes
- Metal / Alloy Types: White / Low Melting (UNS L), Tin / Tin Alloy
- Shape / Form: Ingot
-
Supplier: Washington Alloy Co.
Description: Specifications AWS A5.14-89 Class ERNiMo-7 Description Washington Alloy B-2 is a nickel-molybdenum filler metal used for MIG and TIG welding of Hastelloy? B-2 to itself, to steel or to other nickel-based alloys. The weld deposits of this filler metal exhibit
-
Supplier: Universal Wire Works Inc.
Description: Alloy 718 aluminum is a 12% silicon aluminum brazing alloy primarily designed for welding grades 1060, 1100, 3003, 5005, 6061, 6063, and cast alloys A612 and C612. Applications include heat exchangers, pressure vessels, food containers, liquid oxygen
- AA Grade: 718
- Applications: Aerospace / Aircraft (AQ), Pressure Vessel (PVQ), Structural, Other
- Shape / Form: Wire / Shaped Wire
- Standards / Specifications: AMS
-
Supplier: Universal Wire Works Inc.
Description: Alloy 1100 is virtually pure aluminum designed to weld grades 1100 and 3003 aluminum sheets, plates, bars, etc.
- AISI / AA / CDA Grade: 1100
- Applications: Aerospace / Aircraft (AQ), Other
- Light Alloy: Yes
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
-
Supplier: Universal Wire Works Inc.
Description: Alloy 4043 is a 5% silicon aluminum alloy designed to weld many similar and dissimilar cast and wrought aluminum parts. This alloy is excellent for types 4043, 6063, 5052, 6061, 355, 356 and others. Extensively used with the gas tungsten arc and gas metal
- AA Grade: 4043
- Applications: Aerospace / Aircraft (AQ), Other
- Elongation: 8 %
- Shape / Form: Wire / Shaped Wire
-
Supplier: Washington Alloy Co.
Description: Specifications AWS/SFA 5.10 ER4047 AWS A5.8 BalSi-4 Description Washington Alloy 4047 (commonly referred to as “718 aluminum” or AlSi12) is an aluminum filler metal which contains approximately 12% silicon. This alloy is commonly used not only in MIG or
-
Supplier: United Performance Metals
Description: Alloy 263 is a Ni-Co-Cr-Mo-Ti-Al precipitation-harden able alloy. 263 is furnished in the solution-treated condition unless otherwise specified. It exhibits high strength, corrosion resistance, excellent formability, ductility, and weldability. This alloy is normally used
- Features: Corrosion Resistant, Heat Resistant
- Overall Thickness: 0.1770 to 0.2400 inch
- Processing & Finish: Hardened / Heat Treated
- Shape / Form: Sheet, Semi-finished Shape / Mill Stock
-
Supplier: Washington Alloy Co.
Description: Specifications AWS/SFA 5.10 ER4043 Description Washington Alloy 4043 (commonly referred to as AlSi5) is a 5% silicon aluminum filler metal that is available in spools or cut lengths for MIG or TIG processes. This alloy is recommended for welding 3003, 3004, 5052
-
Supplier: Washington Alloy Co.
Description: Specifications AWS/SFA 5.10 ER5556 Description Washington Alloy 5556 is an aluminum filler metal that contains more manganese and zinc with slightly more magnesium than Washington Alloy 5356. This gives Washington Alloy 5556 good ductility and improved crack
-
Supplier: Aleris International, Inc.
Description: Aleris is one of the leading suppliers of common alloy aluminum bare sheet made from recycled aluminum via two different methods: direct-chill and continuous-cast. The Aleris direct-chill casting facility is located in Lewisport, Kentucky, while our continuous casting mini-mills
- AA Grade: 3105
- Coil Stock: Yes
- Features: Coated / Painted, Corrosion Resistant, Cold Finished / Rolled
- Overall Thickness: 0.0120 to 0.2490 inch
-
Supplier: Aleris International, Inc.
Description: Aleris is one of the leading suppliers of common alloy aluminum bare sheet made from recycled aluminum via two different methods: direct-chill and continuous-cast. The Aleris direct-chill casting facility is located in Lewisport, Kentucky, while our continuous casting mini-mills
- AA Grade: 5005
- Coil Stock: Yes
- Features: Anti-slip / Textured, Corrosion Resistant, Cold Finished / Rolled
- Overall Thickness: 0.0170 to 0.2490 inch
-
Supplier: Universal Wire Works Inc.
Description: Alloy 2319 is used on applications requiring good strength at high temperatures (600 degrees F) and many cryogenic and aircraft parts. Primarily used where weld joints are capable of being heat treated to high strength.
- AISI / AA / CDA Grade: 2319
- Applications: Aerospace / Aircraft (AQ), Other
- Light Alloy: Yes
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
-
Supplier: Isabellenhutte USA
Description: Copper-manganese-tin alloy Low-ohmic alternative to MANGANIN® Improved TCR compared to MANGANIN® ISAOHM® Nickel, chrome and additives from aluminum, silicon, manganese and iron High specific
- Alloy: Yes
- Applications: Resistance Alloy / Heating, Other
- Metal / Alloy Types: Copper, Brass or Bronze Alloy (UNS C)
- Shape / Form: Wire / Shaped Wire
-
Supplier: GFS Chemicals, Inc.
Description: ITEM#:671 Al CAS#:7429-90-5 F.W.:26.98 NFPA#:0-1-1 Specific Gravity: 0.000 DOT:NR Descriptions: Nominally 2-5 mesh Specification TEST 1. Insoluble in dil. HCl 0.05% 2. Silicon 0.1% 3. Nitrogen Compounds 0.001% 4. Copper 0.02% 5. Iron 0.1% 6. Manganese 0.002% 7. Titanium 0.03% Properties No
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A)
- Shape / Form: Powder
-
Supplier: SAE International
Description: This specification covers aluminum alloy brazing sheet for use in brazed aluminum joints.
-
Supplier: Leading Edge Metals & Alloys, Inc.
Description: Used in conjunction with Chromel® in type K thermocouples, Alumel®1 is made of nickel, manganese, aluminum and silicon.
- Alloy: Yes
- Applications: Electronics / RF-Microwave
- Metal / Alloy Types: Aluminum / Aluminum Alloy (UNS A), Nickel / Nickel Alloy (UNS N), Other / Miscellaneous Nonferrous (UNS M)
- Overall Length: 75 to 144 inch
-
Supplier: Detroit Torch & Mfg. Co.
Description: Overview: High temp aluminum flux is used to help prevent oxidation during the welding process. Details: High Temp Aluminum gas welding flux is for all aluminum welding. Mixes with water to a paste consistency. Eliminates the need to clean aluminum prior to
- Alloy Type: Aluminum Alloy
- Welding Process / Form: Powder
Find Suppliers by Category Top
Featured Products Top
-
. Once a process is defined, the engineer or quality group should lock down the specific type of aluminum that is best for the application. Company quality groups can identify the material used from the prototype inspection sample warrant and material certification. Engineering can then update the print (read more)
Browse Datasheets for Protomatic, Inc. -
R-110 0.05" thick x 0.200" high x 3" wide pre-painted aluminum stiffener. This part is sometimes used as a splice joint to connect other components. The material is pre-painted Aluminum to provide corrosion resistance. Hole patterns are (read more)
Browse Aluminum and Aluminum Alloys Datasheets for MP Metal Products -
Thin-rolled aluminum and aluminum alloys from Arnold Precision Thin Metals (PTM) are versatile and lightweight and are used in a variety of electrical products packaging and other applications. Aluminum is often the best solution when reduced weight, good conductivity, and high formability (read more)
Browse Aluminum and Aluminum Alloys Datasheets for Arnold Magnetic Technologies -
Alloy 188 is a cobalt-nickel-chromium-tungsten alloy that combines excellent high-temperature strength with very good resistance to oxidizing environments up to 2100°F (1095°C) for prolonged exposures, and excellent resistance to sulfate deposit hot corrosion. It is readily (read more)
Browse Nickel and Nickel Alloys Datasheets for Ulbrich Stainless Steels & Special Metals, Inc. -
, galvanized steel, aluminized steel, aluminum, copper and pre-painted coils. Gages range from .005" to .165", and widths from 1/2" to 48" in various alloys, tempers, and finishes, in simple or complex shapes. M. P. Metal Products Achieves ISO 9001 : 2015 (read more)
Browse Aluminum and Aluminum Alloys Datasheets for MP Metal Products -
Aluminum coil annealing is a secondary process found in most aluminum mills that produce coiled sheet aluminum (read more)
Browse Aluminum Oxide and Alumina Ceramics Datasheets for Saint-Gobain Performance Ceramics & Refractories -
recycled repeatedly without loss of integrity. All of these capabilities make aluminum extrusion a viable and adaptable solution for a growing number of manufacturing needs. Alloys 6061T651 6063T5 6005AT61 (read more)
Browse Datasheets for Ulbrich Stainless Steels & Special Metals, Inc. -
or better are achievable. Linear accuracy is usually quoted as +/-0.010” per inch although +/-0.020” is possible over a length of 3”. Aluminum melts at a relatively low 1,250 – 1,500 °F and exhibits more fluid behavior than many other alloys. This lets it flow (read more)
Browse Metal Casting Services Datasheets for Impro Industries USA, Inc. -
ALUMINUM & ITS ALLOYS Lightweight and versatile material Thin-rolled aluminum and aluminum alloys from Arnold Precision Thin Metals (PTM) are versatile and lightweight and are used in a variety of electrical products packaging and other applications (read more)
Browse Metal Shapes and Stock Datasheets for Arnold Magnetic Technologies -
Constructed of a tough yet easy to machine aluminum alloy, the 1590 series of diecast enclosures are a stronger alternative to a plastic enclosure and also make great stomp boxes. Standard versions are designed to meet IP54, while watertight versions include a gasket and stainless (read more)
Browse Electronic and Instrument Enclosures Datasheets for Hammond Manufacturing Company Inc.
More Information Top
-
Multistage Fatigue Modeling of Cast A356-T6 and A380-F Aluminum Alloys
common fatigue model constants of the A380 aluminum alloy .
-
Friction stir processing and characterisation of A380 cast aluminium alloy
The surfaces of cast A380 aluminium alloy plates were modified by friction stir processing.
-
Recent magnesium alloy development for elevated temperature applications
Figure 4 shows the test data for AE42 alloy which is compared to AZ91D magnesium alloy and A380 aluminium alloy .
-
A New Magnesium Alloy for Automotive Powertrain Applications
Flat specimens were also machined from the aluminum A380 alloy plates and creep-tested at the same condition.
-
New Aspects of Temperature Behavior of AJ52x, Creep Resistant Magnesium Alloy
And these results have been compared to published results for other die-casting magnesium alloys and the aluminum A380 alloy (Fig.18).
-
http://www.enggjournals.com/ijet/docs/IJET14-06-01-399.pdf
Effect of Cooling Rate on Mechanical Behaviour of Bulk Cast of A380 Aluminium Alloy .
-
Mechanical Property Evaluation of Permanent-Mould Cast AM-SC1™ Mg-Alloy
Comparisons are made with data for a number of HPDC magnesium alloys and aluminum A380 alloy .
-
Interfacial Heat Transfer during Die Casting of an Al-Si-Cu Alloy
Detailed measurements were performed using infrared probes and thermocouple arrays that accurately deter- mine both casting and die surface temperatures during the pressure die casting of an aluminum A380 alloy .
-
Developing castability index for magnesium diecasting alloys
Table 2 Chemical composition of magnesium alloys* and A380 aluminium alloy .
-
Formation of Globular Microstructure in A380 Aluminum Alloy by Cooling Slope Casting
• Formation of Globular Microstructure in A380 Aluminum Alloy by Cooling Slope Casting p.272 .