-
Supplier: Dillon Force Measurement
Description: Proven accuracy and ruggedness sets our mechanical force gauge apart in the force measurement industry. The "D" shaped deflection beam is the heart of the Force Gauge system. Highly engineered materials with close machining tolerances and proper heat treatment provide
-
Supplier: ABB Measurement & Analytics
Description: The load cell is a solid tensiometer made from stainless steel with exceptional ruggedness and high spring constant in line with other Pressductor PillowBlock load cells. It can be installed under the bearing housing and senses the vertical force, measuring in both directions.
- Category of Device: Sensor / Transducer
- Force / Load Rating: 44960 lbs
- Load Cell Package: Plate / Platform
- Sensor Technology: Magnetoelastic
-
Supplier: Sensor Developments, Inc.
Description: Model 10293, Window/Sunroof Pinch Force Sensor Kit, is used to measure the pinch force of automatically closing windows, doors, and sunroof systems under defined spring rates and displacements. The sensor features five interchangeable spring packs, adjustable
- Accuracy: 0.1000 ±% Full Scale
- Category of Device: Sensor / Transducer
- Sensor Output: Analog Voltage
-
-
Description: IEC 61300-3-48:2013 describes the procedure required to measure the spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors. Key words: spring compression force, coupling sleeve for rectangular ferrule multi-fibre connectors
-
Description: IEC 61300-3-22:2010 describes the procedure to measure the spring-loaded force applied to a ferrule when the plugs mate with each other during normal service. This measurement procedure is applicable to a connector plug which has a spring-loaded ferrule. Changes from the
-
Supplier: CSA Group
Description: IEC 61300-3-48:2013 describes the procedure required to measure the spring compression force of the coupling sleeve for rectangular ferrule multi-fibre connectors. Key words: spring compression force, coupling sleeve for rectangular ferrule multi-fibre connectors
-
Supplier: CSA Group
Description: IEC 61300-3-22:2010 describes the procedure to measure the spring-loaded force applied to a ferrule when the plugs mate with each other during normal service. This measurement procedure is applicable to a connector plug which has a spring-loaded ferrule. Changes from the
-
Description: IEC 60512-16-9:2008 details a standard test method to determine the holding capacity of grounding contact springs by means of gauges.
-
Supplier: ValueTronics International, Inc.
Description: , insulation test sets, and much more. A physical measurement test detects issues involving temperature, torque, and force, enabling an engineer to troubleshoot and repair problems. No matter what type of physical measurements you need to take, there are affordable solutions
- Calibrator Style: Other Specific Calibration?
- Process, Environmental, Thermodynamic Properties: Temperature
-
Supplier: CSA Group
Description: IEC 60512-16-9:2008 details a standard test method to determine the holding capacity of grounding contact springs by means of gauges.
-
Supplier: Ametek Solartron Metrology
Description: Rugged design with IP 65 rating 0.7 N Tip force ±1, ±2.5, ±5, ±10 mm ranges Tested to 13 million cycles Excellent linearity and repeatability The standard AX range of Spring Push Probes has justifiably become the workhorse of the gauging industry. Very high resolution
-
Supplier: Staubli Electrical Connectors
Description: For mounting on printed circuit boards, touch-protected according to IEC/EN 61010-1. The socket is directly soldered onto printed circuit boards. The right-angled configuration minimizes the force transmitted to the printed circuit board through the plugged-in test lead. Right-angled Ø 4 mm
- Probe Configuration: Pin and Socket, Spring Loaded
- Voltage Rating: 600 to 1000 volts
-
Supplier: Ametek Solartron Metrology
Description: 0.5, 1, 2, 5, 10 & 20 mm measuring ranges Accuracy as low as <0.1 µm Up to 0.01 µm resolution Up to 0.05 µm repeatability Tip force of 0.7 N (options available) IP65 Sealing The DP range of spring push
-
Supplier: Dillon Force Measurement
Description: Proven accuracy and ruggedness sets our mechanical force gauge apart in the force measurement industry. The "D" shaped deflection beam is the heart of the Force Gauge system. Highly engineered materials with close machining tolerances and proper heat treatment provide
-
Supplier: Dillon Force Measurement
Description: Proven accuracy and ruggedness sets our mechanical force gauge apart in the force measurement industry. The "D" shaped deflection beam is the heart of the Force Gauge system. Highly engineered materials with close machining tolerances and proper heat treatment provide
-
Supplier: Dillon Force Measurement
Description: Proven accuracy and ruggedness sets our mechanical force gauge apart in the force measurement industry. The "D" shaped deflection beam is the heart of the Force Gauge system. Highly engineered materials with close machining tolerances and proper heat treatment provide
-
Supplier: Parco Scientific Company
Description: Ohaus spring scales are designed to deliver reproducible results time after time, perfect for general weighing, force experiments, action-reaction demonstrations and much more. These pull type design spring scales feature Ohaus quality with a custom internal spring
- Capacity: 0.5513 lbs
-
Supplier: Parco Scientific Company
Description: Our series of spring scales provides direct readings for force and measurement. Each scale is calibrated in both newtons and grams. These scales incorporate a zero adjustment for accuracy and are color-coded for students to easily differentiate which scale they require. The body
- Capacity: 6.62 lbs
-
Supplier: RS Components, Ltd.
Description: Mechanical force gauge with spring measuring system and pointer display in N and kg. Switchable between peak value reading and continuous measurement. Measures tractive and compressive forces, with zero position and tare function. Measurement accuracy ±1%, overload
- Accuracy: 1 ±% Full Scale
- Category of Device: Gauge / Indicator
- Force / Load Rating: 67.44 lbs
- Operating Temperature: 50 to 86 F
-
Supplier: RS Components, Ltd.
Description: Mechanical force gauge with spring measuring system and pointer display in N and kg. Switchable between peak value reading and continuous measurement. Measures tractive and compressive forces, with zero position and tare function. Measurement accuracy ±1%, overload
- Accuracy: 1 ±% Full Scale
- Category of Device: Gauge / Indicator
- Force / Load Rating: 22.48 lbs
- Operating Temperature: 86 F
-
Supplier: RS Components, Ltd.
Description: Mechanical force gauge with spring measuring system and pointer display in N and kg. Switchable between peak value reading and continuous measurement. Measures tractive and compressive forces, with zero position and tare function. Measurement accuracy ±1%, overload
- Accuracy: 1 ±% Full Scale
- Category of Device: Gauge / Indicator
- Force / Load Rating: 44.96 lbs
- Operating Temperature: 50 to 86 F
-
Supplier: RS Components, Ltd.
Description: Mechanical force gauge with spring measuring system and pointer display in N and kg. Switchable between peak value reading and continuous measurement. Measures tractive and compressive forces, with zero position and tare function. Measurement accuracy ±1%, overload
- Accuracy: 1 ±% Full Scale
- Category of Device: Gauge / Indicator
- Force / Load Rating: 112 lbs
- Operating Temperature: 50 to 86 F
-
Supplier: Sensor Developments, Inc.
Description: The VHO stands for “Very High Overload” protection in all ranges. Model 10164 incorporates a bidirectional overload protection system. At approximately 130% of the full scale capacity of the load cell, pre-loaded springs are engaged which direct the force path away from the sensing
- Accuracy: 0.1000 ±% Full Scale
- Category of Device: Sensor / Transducer
- Force / Load Rating: 5 to 100 lbs
- Load Cell Package: Canister
-
Supplier: Piezo-Metrics
Description: miniature package. Keeping the sensor small minimizes perturbations in the normal stress field. The DBST’s high spring constant allows measurement of stress in viscoelastic materials. It’s high frequency and overrange capability allows the 100 psi sensor to work up to 3000 psi
- Category of Device: Sensor / Transducer
- Load Cell Package: Miniature
- Operating Temperature: -100 to 325 F
- Sensor Output: Analog Voltage
-
Supplier: ASTM International
Description: 1.1 This test method covers the measurement of the magnetically induced torque produced by the static magnetic field in the magnetic resonance environment on medical devices and the comparison of that torque a user-specified acceptance criterion. 1.2 This test method does not address
-
Supplier: Accuris
Description: German Language - CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 16-9: MECHANICAL TESTS ON CONTACTS AND TERMINATIONS - TEST 16J: GROUNDING CONTACT SPRING HOLDING FORCE
-
Supplier: Accuris
Description: Japanese Language - CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 16-9: MECHANICAL TESTS ON CONTACTS AND TERMINATIONS - TEST 16I: GROUNDING CONTACT SPRING HOLDING FORCE
-
Supplier: Accuris
Description: CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS - PART 16-9: MECHANICAL TESTS ON CONTACTS AND TERMINATIONS - TEST 16I: GROUNDING CONTACT SPRING HOLDING FORCE
-
Supplier: Accuris
Description: CONNECTORS FOR ELECTRONIC EQUIPMENT - TESTS AND MEASUREMENTS PART 16-9: MECHANICAL TESTS ON CONNECTIONS AND TERMINATIONS - TEST 16I: GROUNDING CONTACT SPRING HOLDING FORCE
-
Supplier: Transcat, Inc.
Description: Product Highlights Inside dimension (ID) measurement capability for making comparison measurements of hole diameters and groove and tube thickness Spring-loaded for point contact at constant measuring pressure Dial display provides precise, readable measurements in
- Type: Bore Gage
-
Supplier: Transcat, Inc.
Description: Product Highlights Inside dimension (ID) measurement capability for making comparison measurements of hole diameters and groove and tube thickness Spring-loaded for point contact at constant measuring pressure Dial display provides precise, readable measurements in
- Type: Caliper
-
Supplier: Ametek Solartron Metrology
Description: Accuracy better than 3 µm Measurement range 0.5 mm Spring Actuation 2 g to 20 g tip force Solartron’s Digital Lever Probe has been conceived for the precision measurement market. The probe is ideally suited to applications where the use
-
Supplier: Mark-10 Corporation
Description: Designed to engage the tab on a flip cap for pull-off force measurements. A spring-loaded hook retracts as it is lowered into the starting position, then snaps into place below the tab.
- Type: Test Grip / Clamp
-
Supplier: Trans-Tek, Inc.
Description: balance of mechanical frequency response and tip force. Available in strokes ranging from ± 0.005? to ± 1.0?, these sensors are ideally suited to material thickness measurements, single or multi-point surface profiling, creep testing, or any other application requiring the use of a
- Linearity: 0.2000 ±% Full Scale
- Measurement Range: 0.5000 to 0.9200 inch
- Operating Temperature: -65 to 400 F
- Output: Voltage
-
Supplier: Trans-Tek, Inc.
Description: balance of mechanical frequency response and tip force. Available in strokes ranging from ± 0.005? to ± 1.0?, these sensors are ideally suited to material thickness measurements, single or multi-point surface profiling, creep testing, or any other application requiring the use of a
- Linearity: 0.2000 ±% Full Scale
- Measurement Range: 0.0500 to 0.3500 inch
- Operating Temperature: -4 to 176 F
- Output: Voltage
-
Supplier: Mahr Inc.
Description: indicator. During the measurement, the weight of the gage rests on the anvil spindle Direct indication and evaluation of measurement results Constant measuring force as a result of built-in spring, thus eliminating user influence
- Display: Dial / Analog / Direct Reading Scale
- Mounting / Loading Options: Handheld / Portable
- Range: 0.3937 to 19.69 inch
- Technology: Mechanical
-
Supplier: Mark-10 Corporation
Description: The TSF Force Measurement Test Stand is ideal for spring testing, destructive testing, product integrity testing, and other applications requiring up to 1,000 lbF (5 kN) of push or pull force. The stand features a large side mounted hand wheel requiring minimal user
- Force / Load Capacity: 1000 lbs
-
Supplier: Mark-10 Corporation
Description: The TSF Force Measurement Test Stand is ideal for spring testing, destructive testing, product integrity testing, and other applications requiring up to 1,000 lbF (5 kN) of push or pull force. The stand features a large side mounted hand wheel requiring minimal user
- Force / Load Capacity: 1000 lbs
-
Supplier: Jergens, Inc.
Description: AK2-VT-SO is designed for a M5 socket head screw and is suitable for clamping of relatively small workpieces. Always comes with smooth jaws and Viton O-rings instead of the regular springs. Part Number BK2-VT-O comes with serrated jaws. Part Number BK2-VT-SO is an analogue of BK2-VT-O, with
- Clamping Force: 3372 lbs
-
Supplier: Mark-10 Corporation
Description: This fixture is designed to extract a cork stopper out of a bottle for pull force measurements, in conformance with ISO 9727. The G1105 accommodates up to 1.5 L bottles, and is compatible with both natural and synthetic stoppers. To use, load the bottle onto the spring loaded
-
Supplier: West Control Solutions
Description: The Uniflex SG 45 is a transmitter for processing and monitoring input signals form strain gauges, load cells, melt pressure sensors, and resistance bridges. It can be used in practically all industrial applications involving the precise measurement, indication, and processing of
- Form Factor: DIN Rail
- Operating Temperature: -4 to 140 F
- Outputs: Relay
- Sensor Inputs: Strain Gauge / Bridge
-
Supplier: Marposs Corp
Description: range of accessories ensure that Quick Block can be adapted to numerous applications TECH SPECS measuring range from 2 to 10 mm measuring force from 1 to 1.7 N (± 20%) with standard spring operating pressure for the pneumatic cylinder version
- Range: 0.0787 to 0.3937 inch
- Units: Metric
-
Supplier: Mahr Inc.
Description: Fast and reliable measurement Exceptionally low length measuring uncertainty for precision parts and gage monitoring 100% compliant with Ernst Abbe's comparator principle Online temperature monitoring Software-supported measuring force generation
- Display: Digital Display
- Mounting / Loading Options: Benchtop / Floor
- Range: 0.0 to 11.81 inch
- Technology: Electronic
-
Supplier: Alliance Sensors Group
Description: windshields and plastic material. They can therefore satisfy specific measurement requirements where the tip force must consistently be kept at a very minimum value (it is 0,3 N with spring push models and 0,06 N with models without spring). These probes can be supplied
- Range: 0.0197 to 0.1969 inch
- Technology: Mechanical
- Type: Gage Head / Probe
- Units: Metric
-
Supplier: Alliance Sensors Group
Description: windshields and plastic material. They can therefore satisfy specific measurement requirements where the tip force must consistently be kept at a very minimum value (it is 0,3 N with spring push models and 0,06 N with models without spring). These probes can be supplied
-
Supplier: Allied Electronics, Inc.
Description: time and through large temperature variations to maintain the maximum power dissipation capability. Maximum mounting torque to avoid package damage is 8 in.-lbs (0.9 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center
- Category / Application: General Use
- Features: Heat Sink
- Mounting / Packaging: Radial Leads, Other
- Operating DC Voltage: 200 volts
-
Supplier: Allied Electronics, Inc.
Description: time and through large temperature variations to maintain the maximum power dissipation capability. Maximum mounting torque to avoid package damage is 8 in.-lbs (0.9 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center
- Category / Application: General Use
- Features: Heat Sink
- Mounting / Packaging: Radial Leads, Other
- Operating Temperature: -55 to 175 C
-
Supplier: Allied Electronics, Inc.
Description: time and through large temperature variations to maintain the maximum power dissipation capability. Maximum mounting torque to avoid package damage is 8 in.-lbs (0.9 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center
- Category / Application: General Use
- Features: Heat Sink
- Mounting / Packaging: Radial Leads, Other
- Operating DC Voltage: 200 volts
-
Supplier: Allied Electronics, Inc.
Description: time and through large temperature variations to maintain the maximum power dissipation capability. Maximum mounting torque to avoid package damage is 8 in.-lbs (0.9 N-m). If a spring clip is used, a clip force of 8 to 30 pounds (35 to 130 N) is recommended to be applied to the center
- Category / Application: General Use
- Features: Heat Sink
- Mounting / Packaging: Radial Leads, Other
- Operating Temperature: -55 to 175 C
Find Suppliers by Category Top
Featured Products Top
-
. Solartron Metrology Feather touch and Ultra-feathertouch probes provide clear advantages over other technologies. These highly precise, repeatable measurement sensors have low-tip forces down to 0.05N that can measure delicate surfaces with sub micron accuracy in some cases. They are easy to set up and (read more)
Browse Styli and Probes Datasheets for Ametek Solartron Metrology -
application equipment Robust design elements, including a wide cantilever to resist lateral force and dimples on the contact to enhance contact force. Enabling pick and place design, higher height spring fingers support an automated production line (read more)
Browse Board Mount EMI Filters and RFI Filters Datasheets for TE Connectivity -
motion must be normal to the intended measurement. DL - Lever Probe Accuracy better than 3 µm Measurement range 0.5 mm Spring Actuation 2 g to 20 g tip force Click Here to see the Lever Probe on the Solartron Metrology website. (read more)
Browse Dimensional Gages and Instruments Datasheets for Ametek Solartron Metrology -
The Orbit® GCS is a suite of software that provides Measurement and Gauging functionality with Solartron’s Orbit® Gauging Probes and the (read more)
Browse Dimensional Gages and Instruments Datasheets for Ametek Solartron Metrology
More Information Top
-
Pressure Drop And Closure Forces In Velocity Type Subsurface Safety
Spring Force Measurement Assembly .
-
Fundamentals of Friction and Wear
Driving-velocity dependence of the spring force measured while shearing two adsorbed monolayers of the 12-3-12-3-12 surfactant under a load of L = 4.51 mN at T = 20 C.
-
The effects of load-sensitive behavior on the operability margins of motor-operated gate valves
In each case, the higher absolute value represents the torque measured in the stem, while the lower one represents the stem torque calculated from the operator's mechanical worm gear radius and the torque spring force measurement .
-
Behavior of adhesive boundary lubricated surfaces under
shear: A new dynamic transition
Fig. 2 – Driving-velocity dependence of the spring force measured while shearing two adsorbed mono- layers of the 12-3-12-3-12 surfactant under a load of L = 4.51 mN at T = 20 ◦ C.
-
In vivo stiffness measurement and in silico stiffness prediction of biceps brachii muscle using an isometric contraction exercise
Finally, comparing the spring force measured in the load cell experiment with the calculated value in the LifeMOD simulation analysis using modified-Hill based model, the validity of the developed muscle spring model was verified [17-20].
-
Damper modules with adapted stiffness ratio
Spring Force Measurement .
-
Condition-based preventive maintenance of main spindles
Acceleration Acoustic Emission Internal spring force measurement .
-
Design Criteria For Selecting Velocity Type Subsurface Safety Valves
SPRING FORCE MEASUREMENT .
-
Fairly direct hit! Advances in imaging of shotgun projectiles in MRI
During translational spring force measurements distinct dis- lodgement and torque movement of the ferro- and paramagnetic-composed bullets was observed.