Safety Ohm Meters

Description: current measurement 600 V AC and DC voltage measurement True-RMS AC voltage and current for accurate measurements on non-linear signals Resistance measurement up to 40 k ohm with continuity detection Slim, ergonomic design CAT IV 300V/CAT III 600 V safety

Description: design Large, easy to read backlight display CAT IV 300V/CAT III 600 V safety rating Hold button Two-year warranty Includes: Fluke 324 Clamp Meter Test leads Soft case User's Manual True

Description: measurement Slim, ergonomic design Large, easy to read backlight display CAT IV 300V/CAT III 600 V safety rating Hold button Two-year warranty Includes: Fluke 325 Clamp Meter Test leads Soft case

Description: Includes: Soft carrying case, TL75 test leads, Two AA Alkaline batteries, Coated instruction card, and Safety information sheet Connect your meter to your smartphone with Fluke Connect Measurements Read measurements on your phone at a safe distance, wearing less PPE

Description: Full auto range for V.A and O functions. Data hold function freezes the reading in dimly lit or hard to reach places. Low battery indication. Built-in buzzer for continuity test. Safety design throughout with no exposed metal parts

• Display Digits: 3 Digits
• Features: Battery Powered
• Form Factor: Clamp Meter
• Resistance / Impedance Range: 0.0 to 2 kohms

Description: MEASURED 0.5 INCH JAW OPENING 40 MEGA OHM RESISTANCE RANGE 200 AMPERE AC CURRENT RANGE 750 V AC VOLTAGE RANGE 1000 V DC VOLTAGE RANGE SAFETY RATING CAT IV 600 V CL MODEL

• AC Current Range: 200 amps
• AC Voltage Range: 750 volts
• DC Voltage Range: 1000 volts
• Measurement Type: AC / DC

Description: MEASURED 1 INCH JAW OPENING 20 MEGA OHM RESISTANCE RANGE 600 AMPERE AC CURRENT RANGE 600 V AC VOLTAGE RANGE 600 V DC VOLTAGE RANGE SAFETY RATING CAT III 600 V SERIES CL MODEL

• AC Current Range: 600 amps
• AC Voltage Range: 600 volts
• DC Voltage Range: 600 volts
• Measurement Type: AC / DC

Description: AMPS, CAPACITANCE, FREQUENCY, CONTINUITY PARAMETER MEASURED 1.25 INCH JAW OPENING 40 MEGA OHM RESISTANCE RANGE 400 AMPERE AC CURRENT RANGE 750 V AC VOLTAGE RANGE 1000 V DC VOLTAGE RANGE SAFETY RATING CAT III 600 V CL MODEL

• AC Current Range: 400 amps
• AC Voltage Range: 750 volts
• DC Voltage Range: 1000 volts
• Measurement Type: AC / DC

Description: 0.63 INCH JAW OPENING 40 MEGA OHM RESISTANCE RANGE 200 AMPERE AC CURRENT RANGE 750 V AC VOLTAGE RANGE 1000 V DC VOLTAGE RANGE SAFETY RATING CAT IV 600 V DROP PROTECTION 6.6 FT SERIES CL MODEL

• AC Current Range: 200 amps
• AC Voltage Range: 750 volts
• DC Voltage Range: 1000 volts
• Measurement Type: AC / DC

Description: Sifam Tinsleys (ST) Delta 1000/300 measures important electrical parameters like AC Current (TRMS), DC Current, AC Voltage(TRMS), and DC Voltage. It also features Capacitance, Ohm & Continuity, frequency, and Duty cycle and temperature measurement. KEY FEATURES

• Electrical Measurements: Continuity Check
• Measurement Type: AC / DC

Description: • Certified to EN61010-1 to 600V, Category lll • Self contained AC current measurement up to 10 Amps • Overload protection available This new volt-ohm meter is suitable for testing practically all commercial and industrial installations and is rated to Category III-600V applications.

• AC Voltage Range: 600 volts
• DC Voltage Range: 600 volts

Description: The 6917 motor stator test system collocates the MT-6917 and the 6905 tester. Optional 6420 LCR Meter for testing inductor. It is provided with eight 4-line independent measurement test points and 17 channels. The testing projects include the DC resistance tests which may detect the errors of

• Features: Data Storage
• Form Factor: Stand Alone / Bench
• Operating Humidity: 20 to 90 % (non-condensing)
• Operating Temperature: 10 to 40 C

Description: The 6913 motor stator test system collocates the MT-6913 and the 6905 tester. Optional 6420 LCR Meter for testing inductor. It is provided with eight 4-line independent measurement test points and 13 channels. The testing projects include the DC resistance tests which may detect the errors of

• Features: Data Storage
• Form Factor: Stand Alone / Bench
• Operating Humidity: 20 to 90 % (non-condensing)
• Operating Temperature: 10 to 40 C

Description: The 6910 motor stator test system collocates the MT-6910 and the 6905 tester. Optional 6420 LCR Meter for testing inductor. It is provided with eight 4-line independent measurement test points and 8 channels. The testing projects include the DC resistance tests which may detect the errors of

• Features: Data Storage
• Form Factor: Stand Alone / Bench
• Operating Humidity: 20 to 90 % (non-condensing)
• Operating Temperature: 10 to 40 C

Description: The Clamp-on Meter Model 503 is a general-purpose professional instrument. A strong mechanical case design, quality materials, full ranges and compliance to international safety and quality standards ensure a professional and reliable tool. The Model 503 is auto-ranging, and measures

• Measurement Type: AC / DC

Description: 0 to 400 VAC/VDC, 0.1 Ohms Resolution, Clamp Meter The Fluke 322 is designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. These small and rugged clamp meters are ideally suited for current measurements up to 400 A

• AC Current Range: 0.0 to 400 amps
• AC Voltage Range: 0.0 to 400 volts
• DC Voltage Range: 0.0 to 400 volts
• Measurement Type: AC, DC, AC / DC

Description: 0 to 400 VAC/VDC, 0.1 Ohms Resolution, Clamp Meter The Fluke 321 and 322 are designed to verify the presence of load current, AC voltage and continuity of circuits, switches, fuses and contacts. These small and rugged clamp meters are ideally suited for current measurements up

• AC Current Range: 0.0 to 400 amps
• AC Voltage Range: 0.0 to 400 volts
• DC Voltage Range: 0.0 to 400 volts
• Measurement Type: AC, DC, AC / DC

Description: For those who prefer traditional analog clamp meters, the 710 series hits the spot. Accurate, easy-to-read analog measurements. Features: - 600A AC current capability - Large, optically clear window - Pointer lock - Ohm scale on dial drum - Range finder symbols

Description: 24V loop power supply - HART mode setting with loop power (adds 250ohm resistor) - Double-sized, dual display - 20mA drive into 1200ohms - Backlight with two brightness settings - 0 to 100% mA Span Check buttons to toggle between 4 and 20mA - Infrared I/O serial port compatible with

Description: on V, ohms, frequency 150V overload protection on mA, backed-up by 440 mA 1000V fuse Designed to meet 1000 volt IEC 1010 Cat III standards Simultaneous mA and % of scale readout on mA output - 25% Manual Step plus Auto Step and Auto Ramp on mA output - Min/Max/Average/Hold /Relative modes -

Description: parallax elimination. The Model 260-8Xi offers all of the advantages of the Simpson Model 260-8, plus several new safety features. The bright yellow ABS housing is easy to see and also provides increased drop protection. The Model 260-8XPi includes a resettable overload protection circuit and

• Form Factor: Clamp Meter, Handheld

Description: + DC) CAT III 1000 V/ CAT IV 600 V safety rating Features: Wide measurement ranges to cater for a broad range of applications (ACA, DCV, ACV, OHM, audible continuity, diode and frequency tests.) Auto-ranging capability Built-in peak hold for in-rush current measurement Temperature and

• AC Current Range: 40 to 1000 amps
• AC Voltage Range: 400 to 1000 volts
• DC Voltage Range: 400 to 1000 volts
• Features: Battery Powered

Description: conformity to safety standards EN61010-1, EN61010-2-031, EN61010-2-032 (CAT. m 600 V, CAT. II1000 V) Display (LCD, Digital Counts) 3999 AC Current Accuracy (400A Reference) 1.0+3(50/60Hz) 2.0+3(40~1kHz) AC

• AC Current Range: 2000 amps
• Measurement Type: AC / DC

Description: The Clamp-on Meter Model 502 is a general-purpose professional clamp-on. A strong mechanical case design, quality materials, full ranges and compliance to international safety and quality standards ensure a professional and reliable tool. The Model 502 is a True RMS clamp-on which

Description: -Ranging & ADC Zero Push-button • Data HOLD & PEAK Functions • Relative Function to Compare Two Measurements • Ohm Range & Continuity Test with Beeper, 600V Protection • Batteries: AUTO-OFF and Low Battery Indicator • IEC/EN 61010 Safety Rated & CE Mark

• AC Current Range: 100 amps
• AC Voltage Range: 600 volts

Description: = 200A ac Absolute Maximum DC Current Measurement = 200A dc Absolute Maximum AC Voltage Measurement = 400V ac Absolute Maximum DC Voltage Measurement = 400V dc Absolute Maximum Resistance Measurement = 400Ohms Model Number = CHB15-D AC Current Measurement Resolution = 10mA ac DC Current

• Form Factor: Clamp Meter
• Resistance / Impedance Range: 0.4000 kohms

Description: allows replacement or connection of fused test leads. Safety to EN61010-01 600 V CAT III for industrial environments Absolute Maximum AC Current Measurement = 200A ac Absolute Maximum AC Voltage Measurement = 600V ac Absolute Maximum Resistance Measurement = 2000Ohms Model Number

• Form Factor: Clamp Meter
• Resistance / Impedance Range: 2 kohms

Description: = 600A dc Absolute Maximum AC Voltage Measurement = 600V ac Absolute Maximum DC Voltage Measurement = 600V dc Absolute Maximum Resistance Measurement = 60kOhms Model Number = AMP 220 Best DC Current Accuracy = ±2 % + 5LSD Clamp Meter Type = Current, Voltage Best AC Current Accuracy =

• Form Factor: Clamp Meter
• Resistance / Impedance Range: 60 kohms

Description: = 60kOhms Model Number = AMP 320 Calibrated = UKAS Best DC Current Accuracy = ±2 % + 5LSD Clamp Meter Type = Current, Voltage Best AC Current Accuracy = ±2 % + 5LSD

• Form Factor: Clamp Meter
• Resistance / Impedance Range: 60 kohms

Description: resistance measurement up to 3G ohm RMS value with distorted wave from Auto and manual ranging modes Data hold function Display with backlit

• AC Voltage: 1 to 5000 volts
• Display: Digital Meter
• Form Factor: Portable
• Type of Measurements: Insulation Resistance

Description: Each Kit Includes 5217 Digital Multimeter 400D-10 Current Meter with 10" Flexible Sensor NC-1 Non-Contact Voltage Detector 6527 1kV Megohmmeter Tool Bag Reversible Pocket Screwdriver Product Highlights This kit

Description: The Model 5233 is a rugged, economical TRMS digital multimeter with a function for non-electrical contact testing (NCV) function for detecting live electrical circuits. This multimeter is designed for safety: IEC61010, 600V CAT IV. The Multimeter Model 5233 provides a Volt, Ohm,

Description: Power & Versatility for your Most Demanding Electrical Safety Test Applications Vitrek built the 95X Series from the ground up with DSP technology – to bring you the safest, fastest, most capable, feature rich hipot testers available. The 95X Series combines high output

• AC Voltage: 20 to 10000 volts
• Current Leakage Range: 0.0 to 200 milliamps
• DC Voltage: 20 to 15000 volts
• Display: Digital Meter, LED Indicator

Description: to a standard analog current signal, e.g from valves or Ohmic level sensors. Amplification of bipolar mV signals to standard 4...20 mA current signals. Up to 63 transmitters (HART® 7) can be connected in a multidrop communication setup. Technical characteristics HART®

• Mounting: DIN Rail Mounting
• Operating Temperature: -40 to 140 F
• Output: Analog Current (e.g., 4-20 mA)
• Reference Material: Platinum, Nickel / Nickel Alloys

Description: Signal output, to operate amplifier:0.2 Volts RMS minSignal output, for safety:6.0 Volts peak maxDC resistance:1000 ohms +/- 14% Insulation resistance, wires to probe:500V testMounting thread:5/8 UNF, 18TPIMax recommended lead length:2 meters6.5 feet Probe pressure above