-
Supplier: Hilliard Corporation (The)
Description: weights to fine tune the clutch to keep the rpm in a band close to peak engine torque. This is very important for sprint racing to get the best acceleration off the corners. The Fire clutch is ideal for the LO206 engine because of the smooth engagement and the ability to tune
- Application / Type: Automotive, Other
- Clutch Engagement: Friction
- Drive / Load Connection: Through Shaft
- Shaft Configuration: In-line
-
Supplier: Ogura Industrial Corp.
Description: independently from power fluctuation. NO CONTAMINATION Units are sealed to protect against contamination from equipment. There are also no wear particles from operation to contaminate equipment. TORQUE PROPORTIONAL TO SPEED Unlike centrifugal clutches that use friction surfaces
- Bore Diameter: 0.3150 inch
- Brake Engagement: Noncontact
- Clutch Engagement: Noncontact
- Diameter: 2.76 inch
-
Supplier: Caterpillar Oil & Gas
Description: shipped at max rated rpm Cooling System Thermostats and housing, vertical outlet Jacket water pump — belt-driven, centrifugal Water pump, inlet RH front vertical inlet (pointing down) Exhaust System
- Application: Industrial
- Displacement: 7.24 liters
- Engine Type: Internal Combustion
- Features: EPA Certified, EU Certified, EPA Tier 2/EU Stage II, EPA Tier 3/EU Stage IIIA
-
-
Supplier: Caterpillar Oil & Gas
Description: -280 bkW (275-375 bhp) @ 1800-2200 rpm, meet China Stage II, EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. U.S. EPA Tier 3 equivalent and EU Stage IIIA equivalent ratings are available using U.S. EPA and EU Flexibility. They are also available in other regulated and non
- Application: Industrial
- Displacement: 8.82 liters
- Engine Type: Internal Combustion
- Features: EPA Certified, EU Certified, EPA Tier 2/EU Stage II, EPA Tier 3/EU Stage IIIA
-
Supplier: Caterpillar Oil & Gas
Description: , cementing units, coil tubing units, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty. C9 ACERT hazardous location engines, with ratings 254 bkW (340 bhp) @ 2200 rpm
- Application: Industrial
- Displacement: 8.82 liters
- Engine Type: Internal Combustion
- Features: EPA Certified, EU Certified, EPA Tier 2/EU Stage II, EPA Tier 3/EU Stage IIIA
-
Supplier: Caterpillar Oil & Gas
Description: , with ratings: 242-254 bkW (325-340 bhp) @ 2200 rpm meet IMO Tier II, EPA Non-road Tier 3 equivalent and EU Stage IIIA equivalent emission standards. They are available using U.S. EPA and EU Flexibility, and for other regulated and non-regulated areas. Engine Design
- Application: Industrial
- Displacement: 8.82 liters
- Engine Type: Internal Combustion
- Features: EPA Certified, EU Certified, EPA Tier 2/EU Stage II, EPA Tier 3/EU Stage IIIA
Find Suppliers by Category Top
More Information Top
-
CR4 - Thread: Suffolk Punch Drive
It's a centrifugal clutch - once the RPM gets high enough, it engages.
-
Best Practices for an SAE SUPERMILEAGE® Vehicle
Most common centrifugal clutches engage at 1100 RPM .
-
Development of a 150cc, 4-Valve CVT Engine for Future Emission and Noise Limits
The slipping range of the centrifugal clutch is at 4,000 rpm and at a part load of around 1kW output and at 6,000 rpm with 2.2 kW power a typical CVT variating speed occurs in the ECE 40 driving …
-
CR4 - Thread: Husqvarna's built-in chain brake problem-repair how-to
• When installed on the saw, the saw can be started but cannot be rev'ed to cutting (top rpm ) speed; the centrifugal clutch mechanism that turns with the main drive shaft engages a clutch drum which in turn (being gripped by the …
-
CR4 - Thread: Husqvarna's built-in chain brake problem-repair how-to
• When installed on the saw, the saw can be started but cannot be rev'ed to cutting (top rpm ) speed; the centrifugal clutch mechanism that turns with the main drive shaft engages a clutch drum which in turn (being gripped by the …
-
CR4 - Thread: R&D Assistant Engine Bicycle
I took the bike to the bottom of a steep slope, and while I'm walking aside the bike, I pressed the gas lever to gain 4000 rpm ,below- the centrifugal clutch wouldn't engage the engine to the wheels.I walked carefully aside …
-
An Intercomparison Between a Primary Standard Mercury Barometer and a Gas-operated Pressure Balance Standard
The load is set in rotation at speeds of up to 1000 rpm by a commercial motor and centrifugal clutch system.
-
THE ENERGY RETENTION OF LAMBS GRAZING S37 COCKSFOOT, S23 RYEGRASS AND S24 RYEGRASS AT LOW GRAZING PRESSURE
All cutting was done with a modified gang mower on which the cutting cylinder was driven at approximately 700 rpm by a 4 hp engine with a centrifugal clutch .
-
ASII Ultrasport 254
and
331
Centrifugal sprag clutch for starting engages rotors at 2,000 engine rpm and automatically disengages in the event of engine failure.
-
BAE Systems Land Systems Stormer 30 armoured reconnaissance vehicle
… m Gradient: 60% Side slope: 40% Vertical obstacle: 0.60 m Trench: 2 m Engine: Cummins 6B-275 6-cylinder diesel developing 250 hp at 2,600 rpm Transmission: David Brown Engineering … … with integral steering system Clutch : centrifugal clutch Final drive: single …