-
Description: IC MOTOR DRIVER SER 28SO
- Operating Temperature: -40 to 302 F
- Product Type: H Bridge
-
Motor Controllers - Integrated Circuits (ICs) - PMIC - Motor Drivers, Controllers -- LV8413GP-TE-L-H
Description: H-BRIDGE INTO TWO-CHANNEL MOTOR
- Continuous Output Current: 0.4 amps
- Operating Temperature: -30 to 85 C
-
Supplier: Critical Velocity Enterprises, LLC
Description: Designed with the serious builder in mind, this H-bridge provides 2 Amps continuous with no additional heat sinks. Competing controllers dissipate as much as 26 watts of heat at 2 amps, requiring massive heat sinks to prevent them from burning up. Our efficient H-bridge
- Maximum Output Voltage: 7 to 28 volts
- Rated Power: 112.00000000000013 watts
- Continuous Output Current: 2 amps
- Supply Voltage (DC): 7 to 28 volts
-
-
Description: H-BRIDGE X 4-CH MOTOR DRIVER
-
Supplier: Critical Velocity Enterprises, LLC
Description: Designed with the serious builder in mind, this H-bridge provides 2 Amps continuous with no need for heatsinks. Competing controllers dissipate as much as 26 watts of heat at 2 amps, requiring massive heat sinks to prevent them from burning up. Our efficient H-bridge will
- Maximum Output Voltage: 7 to 28 volts
- Rated Power: 55.999999999999986 watts
- Continuous Output Current: 2 amps
- Supply Voltage (DC): 7 to 28 volts
-
Supplier: Win Source Electronics
Description: Win Source Part Number: 1073043-LV8402GP-H Category: Integrated Circuits (ICs)>PMIC - Motor Drivers, Controllers Package: Tube Applications: General Purpose Standard Package: 490 Mounting: SMD (SMT) Technology: Bi-CMOS Current - Output: 1.4A Function: Driver - Fully Integrated,
- Continuous Output Current: 1.4 amps
- Supply Voltage (AC): 2.8 to 5.5 volts
- Supply Voltage (DC): 2.8 to 5.5 volts
- Operating Temperature: -30 to 85 C
-
Supplier: Infineon Technologies AG
Description: threshold (7A typ.) the H-Bridge switches into chopper current limitation mode. The MOTIX™ TLE9201SG is protected against short circuits and over temperature and provides diagnosis via SPI or basic error feedback via status flag. Open load can be detected when the bridge
- Supply Voltage (DC): 5 to 36 volts
- Operating Temperature: -40 to 125 C
- Motor / System: DC Brushed Motor
- Configuration: IC / PCB-Mounted
-
Supplier: Win Source Electronics
Description: Win Source Part Number: 969965-LB1867M-TLM-H Category: Integrated Circuits (ICs)>PMIC - Full, Half-Bridge Drivers Package: Tape & Reel (TR) Applications: DC Motors, General Purpose Standard Package: 1,000 Mounting: SMD (SMT) Technology: Bipolar Interface: Logic Current -
- Supply Voltage (Vi): 6.4 to 7 volts
- Operating Temperature: -30 to 80 C
- Output Options: Inverting
-
Supplier: ROHM Semiconductor GmbH
Description: The BD6736FV motor driver provides 1 Full-ON Drive H-bridge channel, while BD6735FV provides 2 Full-ON Drive H-bridge channels. These ICs feature low power consumption by low ON-resistance with built-in charge pump circuit for the upper DMOS gate drive in a
- Peak Output Current: 1 amps
- Supply Voltage: 10 volts
- Operating Temperature: -30 to 75 C
- Number of Outputs: 1
-
Supplier: ROHM Semiconductor USA, LLC
Description: The BD6736FV motor driver provides 1 Full-ON Drive H-bridge channel, while BD6735FV provides 2 Full-ON Drive H-bridge channels. These ICs feature low power consumption by low ON-resistance with built-in charge pump circuit for the upper DMOS gate drive in a
- Peak Output Current: 1 amps
- Supply Voltage: 10 volts
- Operating Temperature: -30 to 75 C
- Number of Outputs: 2
-
Supplier: Progressive Automations
Description: is over 1200W of power! The MegaMoto GT is a dual half-bridge circuit that can be configured either has a full H-bridge or as two independent half-bridge circuits. This allows a single MegaMoto GT to drive one motor with full variable-speed control
- Supply Voltage (DC): 6 to 35 volts
- Continuous Output Current: 35 amps
- Peak Output Current: 50 amps
- Features: Alarm / Status Monitoring
-
Supplier: Acme Chip Technology Co., Limited
Description: 1.2A DUAL H-BRIDGE MOTOR DRIVER
- Continuous Output Current: 2 amps
- Operating Temperature: -30 to 85 C
-
Supplier: Acme Chip Technology Co., Limited
Description: H-BRIDGE MOTOR DRIVER
-
Description: IC MOTOR DRIVER PAR 20TSSOP
- Features: Other
- Packing Method: Tape Reel
-
Supplier: Aratas America LLC
Description: Low Profile Low Load Relay with H-Bridge Circuit Inside for Motor Control Applications Low profile and can switch 14 V 25 A motor load H-Bridge circuit inside Pin in paste reflow compliant relay Temperature range -40°C to +125°C
- Features: Other
-
Supplier: Win Source Electronics
Description: Half Bridge Load Type: Inductive Categories: Integrated Circuits Supplier Device Package: 9-SIP, 7 Leads Status: Obsolete Temperature Range - Operating: -55°C ~ 150°C Manufacturer Homepage: www.irf.com Manufacturer Package: 9-SIP, 7 Leads Popularity: Medium Fake Threat In the Open
- Supply Voltage: 10 to 15.6 volts
- Operating Temperature: -55 to 150 C
- Features: Other
- Packing Method: Tube
-
Supplier: Win Source Electronics
Description: Manufacturer: ON Semiconductor Win Source Part Number: 205950-LA6584M-MPB-H Packaging: Reel - TR Applications: DC Motors, General Purpose Mounting: SMD (SMT) Technology: Bipolar Voltage - Load: 2.8 V to 14 V Load Type: Inductive Categories: Integrated Circuits Status:
- Supply Voltage: 2.8 to 14 volts
- Operating Temperature: -30 to 90 C
- Features: Other
- Packing Method: Tape Reel
-
Supplier: Infineon Technologies AG
Description: the implementation of advanced motor control algorithms. It includes four fully integrated NFET drivers optimized to drive a 2-Phase motor via four external power NFETs, a charge pump enabling low voltage operation and programmable current along with current slope control for optimized
- Clock Speed: 40 MHz
- Supply Voltage (Vcc): 5.5 to 28 volts
- Operating Temperature: -40 to 150 C
- Bits: 32 Bit
-
Supplier: Infineon Technologies AG
Description: The device is designed for various motor control automotive applications. To support these applications, the device provides the main functions, such as a 5 V lowdropout voltage regulator one HS-CAN transceiver supporting CAN FD, CAN Partial Networking (incl. FD Tolerant Mode), three
- Supply Voltage (DC): 5.5 to 28 volts
- Operating Temperature: -40 to 150 C
- Motor / System: DC Brushless Motor
- Phase: Three Phase
-
Supplier: ROHM Semiconductor USA, LLC
Description: BD6382?EFV Series are built-in 2channel H-bridge circuits that can drive 2pcs DC brush motor or stepping motor.
- Operating Temperature: -25 to 85 C
- Screening Level: Commercial
- Features: Other
- Packing Method: Tape Reel
-
Supplier: ERSAELECTRONICS PTE. LTD.
Description: replacement parts, BOM lines, package options, lifecycle status, and procurement availability. Key searchable attributes include Stepper. Search-friendly keywords include motor driver IC, H-bridge, stepper motor, PWM control, motion control, Stepper, Full
- Supply Voltage (DC): 46 volts
- Operating Temperature: 0 C
- Features: Other
-
Supplier: ERSAELECTRONICS PTE. LTD.
Description: parts, BOM lines, package options, lifecycle status, and procurement availability. Key searchable attributes include key electrical ratings, package details, and application requirements. Search-friendly keywords include motor driver IC, H-bridge, stepper motor, PWM
-
Supplier: Microchip Technology, Inc.
Description: internally connected to form six half-bridges and can be controlled separately from a standard serial data interface to combine loads from bulbs, resistors, capacitors, and inductors.The IC supports the application of H-bridges to drive DC motors. Additional Features Six
- Features: Other
- Package Type: SOIC
-
Supplier: ROHM Semiconductor GmbH
Description: BD62110JEFJ is a built-in 1 channel H-bridge motor driver for DC brush motors. This driver can facilitate low power consumption by direct PWM. There are built in protection circuits in this IC. Each protection circuit operation contributes to set high
- Peak Output Current: 1 amps
- Supply Voltage: 36 volts
- Operating Temperature: -25 to 85 C
- Screening Level: Commercial
-
Supplier: ROHM Semiconductor GmbH
Description: BD62221MUV is a built in 2 channel H-bridge motor driver for 2 DC brush motors or 1 stepper motor. This driver can facilitate low power consumption by direct PWM control or PWM constant current control. There are built in protection circuits in this IC. It
- Continuous Output Current: 2 amps
- Supply Voltage (AC): 36 volts
-
Supplier: ROHM Semiconductor GmbH
Description: BD64220EFV is a built-in 2 channel H bridge motor driver for 2 DC brush motors or 1 bipolar stepping motor. This driver can drive high efficiency by direct PWM or PWM constant current control. There are built in protection circuits in this IC. It is possible
- Continuous Output Current: 2 amps
- Supply Voltage (AC): 50 volts
-
Supplier: Microchip Technology, Inc.
Description: connected to form three half-bridges, each separately controllable from a standard serial data interface to combine loads from bulbs, resistors, capacitors, and inductors. The IC supports the application of H-bridges to drive DC motors. Additional Features Supply voltage
- Features: Other
- Package Type: SOIC
-
Supplier: ROHM Semiconductor USA, LLC
Description: BD61243FV is a 1chip driver that is composed of H-bridge power DMOS FET. Moreover, the circuit configuration is restructured, and convenience has been improved by reducing the external parts and simplifying the setting compared with the conventional driver.
- Peak Output Current: 1.2 amps
- Supply Voltage: 18 volts
- Operating Temperature: -40 to 105 C
- Number of Outputs: 1
-
Supplier: Infineon Technologies AG
Description: Peripheral Interface Integrated dual-stage charge pump for reverse battery protection Drain-source monitoring for hard short circuit detection Current sense monitoring for soft short circuit detection Over temperature warning and shutdown Timeout watchdog Detailed off-state diagnostic
- TJ: -40 to 150 C
- Features: Automotive, MOSFET, Other
- Packing Method: Tape Reel
-
Supplier: Richardson RFPD
Description: The circuit is an H-bridge composed of high power switching MOSFETs that are controlled by low voltage logic signals. The circuit provides a convenient interface between logic signals and the high power bridge. The bridge uses low cost N-channel power
- Category: Development Board
-
Supplier: H2W Technologies
Description: Key Features: 20 to 50 VDC Supply Voltage H-Bridge, 2 Phase Bi-polar Micro-stepping Drive Suitable for 2-phase, 4, 6 and 8 leads step motors Compatible with all H2W linear stepper motor models, STS-0213-R, STS-0620-R, STS-1220-A, STS-2030-A Compatible with standard rotary
- Number of Axes / Motors: 1
- Peak Output Current: 1 to 4.2 amps
- Supply Voltage (DC): 20 to 50 volts
- Operating Temperature: 0 to 50 C
-
Supplier: Progressive Automations
Description: The LC-85 is a small high performance single channel H-bridge speed controller for our actuators. It is capable of full speed control of a single actuator and with the addition of relays it can control two. Standard RC pulse format Calibrate function to match unit to radio signal range
- Supply Voltage (DC): 6.5 to 28 volts
- Continuous Output Current: 10 amps
- Peak Output Current: 30 amps
-
Supplier: Nexperia B.V.
Description: printed-circuit board area requirements. AEC-Q101 qualified Applications Power management: Complementary MOSFET driver Dual supply line switching. Peripheral driver: Half and full bridge motor drivers Multi-phase stepper motor driver.
- Features: Other
-
Supplier: Nexperia B.V.
Description: generation Smaller required Printed-Circuit Board (PCB) area than for conventional transistors AEC-Q101 qualified Applications Complementary MOSFET driver Half and full bridge motor drivers Dual low power switches (e.g. motors, fans) Automotive applications
- Transistor Grade / Operating Range: Automotive
- Polarity: Complementary
- Features: Other
Find Suppliers by Category Top
Featured Products Top
-
XCKMR54D1H29 carries an A300 control-circuit designation for AC applications. Under IEC 60947-5-1 conditions, it is rated for AC-15 service at 3 A and 240 VAC, with a conventional enclosed thermal current of 10 A. For DC control circuits, it carries a Q150 (read more)
Browse Electromechanical Relays Datasheets for ERSAELECTRONICS PTE. LTD. -
The YHD-H55 Brushless DC Vacuum Motor is engineered to deliver strong suction performance with quieter operation for modern vacuum cleaner applications. Featuring an optimized brushless DC architecture, advanced magnetic circuit (read more)
Browse DC Motors Datasheets for Shenzhen Yunhongda Motor Co., LTD. -
motors, conveyors, pumps, lighting circuits, HVAC equipment, and other high?demand loads. These relays are widely used across industrial automation, building management systems, power and energy infrastructure, transportation equipment, and medical devices. They deliver stable (read more)
Browse Electromechanical Relays Datasheets for FCL Components America -
as integrated system platforms—pre-equipped with functional components (e.g., circuit breakers) and grounding elements—bridging IT and OT integration while ensuring reliable protection and scalability for industrial servers, controllers, and network components. (read more)
Browse Industrial Chassis and Card Cages Datasheets for TPS Elektronik GmbH -
perfect open-circuit, that is the current can only be zero amps at the open-circuit. Again, Mother Nature gets around the zero amps requirement by creating an equal and opposite signal that travels back down the line. At the open-circuit the +I and -I cancel to give the required zero amps. Technically this should be +H field and -H field, but for our purposes we will stick with +I and -I. (read more)
Browse Antennas Datasheets for A.H. Systems Inc. -
Power electronics systems such as inverters and motor drives require capacitors that deliver stable DC support, low losses, and long-term reliability under electrical and thermal stress. The WLM series DC-Link film (read more)
Browse Film Capacitors Datasheets for Shenzhen Weidy Industrial Development Co., Ltd. -
and Electronics While automated washers achieve exceptional hygiene and process efficiency, they can expose powered hand tools with motors and electronics to harsh conditions, potentially affecting their longevity and performance. The use of steam combined with high pH (alkaline (read more)
Browse Brushless Motors Datasheets for Portescap -
• Skid mounted pumps: with or without motor but suitable for horizontal or vertical mounting. • High efficiency Air/Oil Heat Exchangers: up to 14,000 kCal/h (16kW). (read more)
Browse Screw Pumps Datasheets for jbj Techniques Limited -
stable voltage for motor drive units. Comprehensive electronic protection includes overload, overvoltage and short circuit protection, and thermal shutdown with automatic reset in case of insufficient cooling. This DC-DC regulator is filtered to meet EN55032 Class A EMI with wide margins (read more)
Browse DC-DC Converters Datasheets for ABSOPULSE Electronics Ltd. -
contact pills ensure extremely low contact resistance, minimizing heat generation and significantly reducing the risk of contact welding. The double contact bridge design provides improved arc extinguishing performance. With a making capacity of up to 200 A, the relay is engineered for long (read more)
Browse High Voltage Relays Datasheets for Schaltbau GmbH
More Information Top
Indicates content that may require registration and/or purchase.
-
http://dspace.mit.edu/bitstream/handle/1721.1/43408/37658987-MIT.pdf?sequence=2
A new approach to a DC brush motor control circuit is designed to improve its performance and compactness over a conventional previous PWM H - bridge motor circuit using a Motorola MC33033 chip and a single specialized IC H-bridge motor circuit using …
-
http://www.discovercircuits.com//////////////////////////////////////////////////////////////////////////////////////////////////////////////////PDF-FILES/LOWP...
LOW POWER H BRIDGE MOTOR CONTROL CIRCUIT ALL RIGHTS RESERVED .
-
How a freshman level research initiative evolved into multidiscieplinary teaching tools
… keypad and 4x20 character liquid crystal display for an interactive user interface, an &bit AID converter with a Buttenvorth low- pass filter input circuit for system feedback from a tacho-generator, an integrated H Bridge motor drive circuit and an Atmel 8YCS1 …
-
Arduino Robot Bonanza > The Amazing Tunebot
And second, motor H - bridge circuits are known for producing lots of electrical noise—actually, it's not the H-bridge that makes the noise; it's the motors.
-
Advanced Microsystems for Automotive Applications 2003
H-Bridge drivers with integrated charge pump: The power window block con- trols four conventional power FETs to drive a power window motor ( H - Bridge ) circuit .
-
A compact MCM implementation of an embedded system for automotive applications
It is necessary to perform the followingfunctions: Power window: Driver for the 4 powers FETs that control the power window motor ( H - Bridge circuit ).
-
Modeling and stability analysis of a scaled telemanipulation system
The main parts of the system are master, slave, 386PC, M68HC11 microcontrollers, PWM circuits and H bridge motor drivers.
-
Arduino Robotics
We then discussed the various types of H - bridge motor control circuits and their allowed states.
-
Intermediate Robot Building
The FU5505 is the same one I use in my custom H - bridge motor driver circuit (see Chapter 10).
-
Advanced Power MOSFET Concepts
Two promi- nent examples of such circuits are the voltage regulator module (VRM) used to deliver power to microprocessors in computers and the H - bridge motor control circuits used to achieve adjustable speed drives.