Analog Linear Encoders
from Exsenco, LLC
SANTEST's GYAF1-probe is an all-in-one type sensor with integrated controller. After supplying DC 24V to the probe, an analogue voltage and/or current, which are proportional to the position of the magnet, can be obtained. Reversed output or bipolar output can be supported as well. The flat head... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0250
- Measurement Range: 0.5906 to 118
- Operating Temperature: -4 to 176
from Exsenco, LLC
Thanks to the Surface Mount Technology, the entire signal processing electronics of SANTEST's GYcAT series is integrated into a transducer head. You can get a voltage or current analog signal proportional to a magnet position only by applying a 24V dc power supply directly to the transducer. GYcAT... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0500
- Measurement Range: 0.5906 to 98.43
- Operating Temperature: -4 to 149
from Exsenco, LLC
SANTEST Analogue Output (replacement model for GYLT, GYLS) [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0500
- Measurement Range: 0.5906 to 138
- Operating Temperature: -4 to 176
from Exsenco, LLC
The GYSE-probe is an all-in-one type sensor with positional resolution up to 1 μm. Positon output is Analogue, SSI, or Incremental. Velocity output is optional and is available for Analogue type. The positional difference between 2 magnets can be observable. as well. This allows quick and easy... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0250
- Measurement Range: 0.5906 to 205
- Operating Temperature: -4 to 176
from Exsenco, LLC
SANTEST's GYSE-probe is an all-in-one type sensor with positional resolution up to 1 μm. Position output is Analog, SSI, or Incremental. Velocity output (option) is available for Analog type. The positional difference between 2 magnets can be observable as well. This allows quick and easy sensor... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0250
- Measurement Range: 0.5906 to 205
- Resolution: 0.0020 to 0.0100
from Exsenco, LLC
SANTEST's GYGS probe is a series of which sensor head is extremely thin (20mm thick) adopting new method of detecting magnetostrictive phenomena. Applying to hydraulic cylinder, its total length becomes space saving. GYGS probe is used in combination with the GYGSC controller, which provides... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0250
- Measurement Range: 0.5906 to 118
- Operating Temperature: -4 to 176
from Exsenco, LLC
GYMS probe/GYMSC controller is a compact, low-cost type series. adopting newly developed signal detecting method. GYMS probe has interchangeability in mechanical dimension with GYMT series, also protection graded up to IP67. Optional connector cable out variety presents more flexible handling of... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0250
- Measurement Range: 0.5906 to 118
- Operating Temperature: -4 to 176
from Exsenco, LLC
SANTEST's GYMT series, the compact probe and controller in the GY series, have an extremely simplified and carefully selected electronics in a small place. By employing COMBICON screw plug connectors of Phoenix Contact in the GYMTC controller, wiring operation becomes easier and more reliable. The... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0500
- Measurement Range: 0.5906 to 78.74
- Operating Temperature: 23 to 140
from Exsenco, LLC
SANTEST's GYPE2K probe is a sensor characterized in a fine rod and a small head. A fine rod (outside diameter Φ4) and a small head expand the design flexibility of the equipment. Standard magnet and float can be used. With the GYMSC controller, it outputs analogue signal of 0-10V or 4-20mA. [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.5000
- Measurement Range: 1.97 to 9.84
- Operating Temperature: -4 to 176
from Exsenco, LLC
The sensor head of SANTEST's GYPM probe is more compact. By new design of probe head, screw side dead zone has been shortened to 30mm (Standard). As to tip dead zone, making short to 40mm is possible by option (standard: 70mm). Cable out direction is radial. GYPM probe is used in combination with... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0500
- Measurement Range: 0.5906 to 39.37
- Operating Temperature: 23 to 140
from Exsenco, LLC
SANTEST's GYHR probe is designed to operate at high ambient temperatures up to 100 °C, including sensor head. Electronic parts inside are minimized, yet our device of circuit produces high performance and reliability in the application. Cable used has reinforced silicon rubber sheath which... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.1000
- Measurement Range: 0.5906 to 78.74
- Resolution: 1.00E-3
from Exsenco, LLC
SANTEST's Linear Inductance-L Transducer L2DT is a sensor of which inductance changes with displacement of the copper sleeve covering a sensor probe. 10kHz sine wave excites the solenoid coil of the L2DT sensor. It generates the short ring effect as a copper sleeve covers a sensor probe. The... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.5000
- Measurement Range: 3.94 to 19.69
- Operating Temperature: 32 to 302
from Exsenco, LLC
The profile measuring Φ25mm ×height 22.5mm renders you a free mechanical design in adopting our "GY" series. Applications have been widened by mounting SANTEST's GYKM series to cylinders, machines, equipment and it gives infinite life time due to magnetostrictive non-contact sensor, well... [See More]
- Incremental Encoder Signal: Analog
- Linearity: 0.0500
- Measurement Range: 0.5906 to 47.24
- Operating Temperature: 32 to 149
from BOGEN Magnetics GmbH
IKS15 convinces customers in automation, measurement and control technology with extremely high accuracy and a particularly high degree of modularity. BOGEN offers different variants of the IKS15, which we configure according to customer-specific requirements. In combination with BOGEN precision... [See More]
- Incremental Encoder Signal: Analog
- Encoder Reading: Incremental
- Linear Encoder Technology: Magnetostrictive
from Broadcom Inc.
The AEDR-8320 series is one of the smallest optical encoder employing reflective technology for motion control purposes. The encoder combines an emitter and a detector in a single surface mount leadless package. When used with a codewheel or linear codestrip, the encoder translates rotary or linear... [See More]
- Incremental Encoder Signal: Analog
- Operating Temperature: 14 to 158
- Accuracy: 5 to 12.5
- Linear Encoder Technology: Optical
from RSF Electronics, Inc.
Compact highly integrated design, extremely flat design, high resolution [See More]
- Incremental Encoder Signal: Digital; Analog
- Linear Encoder Speed: 8000
- Resolution: 1.00E-4
- Operating Temperature: 32 to 131
from Broadcom Inc.
The HEDS-97Ex transmissive analog optical encoder is a high performance optical encoder, developed in a small form factor and specially designed for use in applications that requires stepper, BLDC and DC motors to perform its operations . This transmissive analog encoder offers Avago ’s... [See More]
- Incremental Encoder Signal: Analog
- Linear Encoder Technology: Optical
- Operating Temperature: 32 to 140
- Encoder Reading: Incremental