Cobalt End Mills
from RS Components, Ltd.
10 piece end mill set [See More]
- Material: Cobalt; HSCo
- Shank: 0.236 to 0.630
- Cutter: 0.118 to 0.315
- OAL: 2.13 to 3.29
from RS Components, Ltd.
C123 HSCO MILL 2mm [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.079
- OAL: 2.13
from RS Components, Ltd.
C123 HSCO MILL 3mm [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.118
- OAL: 2.20
from RS Components, Ltd.
FC3 MILL 1.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.039
- OAL: 0.96
from RS Components, Ltd.
FC3 MILL STANDARD 2.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.079
- OAL: 1.00
from RS Components, Ltd.
FC3 MILL STANDARD 2.5MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.098
- OAL: 1.02
from RS Components, Ltd.
FC3 MILL STANDARD 3.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.118
- OAL: 1.10
from RS Components, Ltd.
FC3 MILL STANDARD 3.5MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.138
- OAL: 1.18
from RS Components, Ltd.
FC3 MILL STANDARD 4.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.157
- OAL: 1.28
from RS Components, Ltd.
FC3 MILL STANDARD 5.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.197
- OAL: 1.42
from RS Components, Ltd.
FC3 MILL STANDARD 6.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.236
- OAL: 1.42
from RS Components, Ltd.
C247 HSCO-XP E-MILL DIN844K 2.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.079
- OAL: 2.01
from RS Components, Ltd.
C247 HSCO-XP E-MILL DIN844K 2.5MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.098
- OAL: 2.05
from RS Components, Ltd.
C273 HSCO-XP LS E-MILL DIN844L 5.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.197
- OAL: 2.68
from RS Components, Ltd.
C273 HSCO-XP LS E-MILL DIN844L 6.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.236
- OAL: 2.68
from RS Components, Ltd.
C273 HSCO-XP LS E-MILL DIN844L 12.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.472
- Cutter: 0.472
- OAL: 4.33
from RS Components, Ltd.
C273 HSCO-XP LS E-MILL DIN844L 10.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.394
- Cutter: 0.394
- OAL: 3.74
from RS Components, Ltd.
C247 HSCO-XP E-MILL DIN844K 3.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.118
- OAL: 2.05
from RS Components, Ltd.
C247 HSCO-XP E-MILL DIN844K 4.0MM [See More]
- Material: Cobalt; HSCo
- Shank: 0.236
- Cutter: 0.157
- OAL: 2.17
from Universal Cutting Tools, Inc.
4-Flute Double End M42 8% Cobalt End Mill - Regular Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Double
- Cutter: 0.312
from Melin Tool Company
Used for general purpose milling in most materials of medium hardness such as steel, brass, iron, etc. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Ball. Length of Cut: 3/32". Number of Flutes: Overall Length: 2 1/4". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
2-Flute Double End M42 8% Cobalt End Mill - Regular Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Double
- Cutter: 0.312
from Melin Tool Company
Used for radius and contouring part surfaces. Materials ranging from nickel base alloy, stainless, tough alloys, and abrasive materials. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Ball. Flute Length Type: Long. Length of Cut: 7/32". Number of Flutes: Overall Length: 2 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
Multi-Flute Single End M42 8% Cobalt End Mill - Regular Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
General purpose milling in most materials of medium and tough alloy materials, such as stainless steel, nickel base alloy, brass, iron etc. Can be used in profling, slotting, keyways, and pockets. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Ball. Length of Cut: 3/64". Number of Flutes: Overall Length: 2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
Multi-Flute Single End M42 8% Cobalt End Mill - Long Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
Used for radius or contouring part surfaces. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Ball. Flute Length Type: Standard. Length of Cut: 3/32". Number of Flutes: Overall Length: 1 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
Multi-Flute Single End M42 8% Cobalt End Mill - Extra Long Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
Used to machine soft materials such as aluminum, plastic, or zinc alloys. High helix provides positive shearing action and rapid chip removal. Standard, medium, long, and extra long lengths. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 3/16". End Type: Ball. Flute Length Type: Long. Length of Cut: 1". Number of Flutes: Overall Length: 3 3/8". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
2-Flute Single End M42 8% Cobalt End Mill - Regular Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
Used for radius or contouring part surfaces. Designed to machine soft materials such as aluminum, plastic, or zinc alloys. High helix provides positive shearing action and rapid chip removal. Standard, medium, long, and extra long lengths. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Square. Length of Cut: 3/32". Number of Flutes: Overall Length: 2 1/4". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Universal Cutting Tools, Inc.
2-Flute Single End M42 8% Cobalt End Mill - Long Length [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.375
from Melin Tool Company
Used for radius or contouring part surfaces. Materials ranging from nickel base alloy, stainless, tough alloys, and abrasive materials. Standard, medium, and long lengths. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Square. Flute Length Type: Long. Length of Cut: 7/32". Number of Flutes: Overall Length: 2 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Universal Cutting Tools, Inc.
2-Flute Single End M42 8% Cobalt End Mill - Ball Nose [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
General purpose milling in most materials of medium and tough alloy materials, such as stainless steel, nickel base alloy, brass, iron etc. Used to mill keyways to close tolerance. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Square. Length of Cut: 3/64". Number of Flutes: Overall Length: 2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Universal Cutting Tools, Inc.
4-Flute Single End M42 8% Cobalt End Mill - Ball Nose [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.312
from Melin Tool Company
Used when a longer reach is required but not a longer cutting length, such as in deep slots or pockets. Extended unfluted neck to provide greater rigidity and to reduce defection. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/32". End Type: Square. Flute Length Type: Standard. Length of Cut: 3/32". Number of Flutes: Overall Length: 1 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Universal Cutting Tools, Inc.
M42 8% Cobalt End Mill - 60-Degree High-Spiral * Center Cutting [See More]
- Material: Cobalt
- Cutter: 1.000
- Units: Fractional
- Shank: 1.000
from Melin Tool Company
Used when a longer reach is required but not a longer cutting length, such as in deep slots or pockets. Extended unfluted neck to provide greater rigidity and to reduce defection. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Ball. Flute Length Type: Standard. Length of Cut: 3/16". Number of Flutes: Overall Length: 2 1/4". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill - Multi-Flute * Single End * Coarse Pitch [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Melin Tool Company
General purpose milling in most materials of medium hardness such as steel, brass, iron, etc. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Square. Flute Length Type: Long. Length of Cut: 7/32". Number of Flutes: Overall Length: 2 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill - 3-Flute Single End * Stub Length * Fine Pitch * Center Cutting [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Melin Tool Company
General purpose milling in most materials of medium and tough alloy materials, such as stainless steel, nickel base alloy, brass, iron etc. Standard, stub, medium, long, and extra long lengths. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Ball. Flute Length Type: Stub. Length of Cut: 3/32". Number of Flutes: Overall Length: 2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill for Aluminum - 3-Flute Single End * Center Cutting * Coarse Pitch [See More]
- Material: Cobalt
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Melin Tool Company
3 flutes usually allow feed rates 50% faster than 2 flute tools. Used for radius or contouring part surfaces. Can also be used in profling, slotting, key-ways and pockets. Designed to cut materials including nickel base alloy, stainless, tough alloys, and abrasive materials. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Square. Flute Length Type: Standard. Length of Cut: 3/16". Number of Flutes: Overall Length: 2 1/4". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Melin Tool Company
3 flutes usually allow feed rates 50% faster than 2 flute tools. For general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron etc. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Square. Flute Length Type: Stub. Length of Cut: 3/32". Number of Flutes: Overall Length: 2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Used in stainless steel, titanium, Inconel and high temperature alloy materials. High helix increases length of cutting edge which reduces cutting load variation and provides excellent surface finish. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Cutting Edge Technologies, Inc.
Diameter: 1/16". End Type: Square. Flute Length Type: Standard. Length of Cut: 3/16". Number of Flutes: Overall Length: 1 1/2". Shank Diameter: 3/16". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
3 flutes usually allow feed rates 50% faster than 2 flute tools. Used for radius or contouring part surfaces. Designed to cut materials including nickel base alloy, stainless, tough alloys, and abrasive materials. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Ballnose
- Units: Fractional
from Cutting Edge Technologies, Inc.
Coating: Uncoated. Diameter: 0.005". End Type: Square. Flute Length: 3 X DIA. Flute Length Type: Standard. Number of Flutes: Overall Length: 1 1/2". Shank Diameter: 1/8". Tolerance: +/- .0005". Type: End Mill [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
3 flutes usually allow feed rates 50% faster than 2 flute tools. For use when longer reach is required but not a longer cutting length, such as deep slots or pockets. Extended unfluted neck for greater rigidity. Materials include nickel base alloy, stainless, alloys and abrasive materials [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
3 flutes usually allow feed rates 50% faster than 2 flute tools. Used for general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron etc. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Designed to mill chamfers and to countersink. Cobalt HSS (M42) gives high edge hardness at high temperature levels. [See More]
- Material: Cobalt
- Cutting Ends: Double
- Geometry: Chamfer
- Units: Fractional
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. A rough finish is produced which will require a finishing pass. Designed to machine soft materials such as aluminum, plastic, zinc alloys. Wide futes provide rapid chip... [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. A rough finish is produced which will require a finishing pass. Used in difficult and abrasive materials and tough alloy materials, such as stainless steel, nickel base... [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. These tools will plunge cut. A rough finish is produced which will require a finishing pass. Used in diffcult and abrasive materials and tough alloy materials, such as... [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. A rough finish is produced which will require a finishing pass. Used in difficult and abrasive materials and tough alloy materials, such as stainless steel, nickel base... [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Square
- Units: Fractional
from Melin Tool Company
Corner radius allows more strength and minimizes chatter and chipping on corner especially when milling pockets. Used for general purpose milling in most materials of medium and tough alloy materials such as stainless steel, nickel base alloy, brass, iron etc. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Radius
- Units: Fractional
from Melin Tool Company
Designed to produce a radius between a horizontal and vertical surface. Tools are formed-relieved which allows the form and size to be maintained after resharpening. [See More]
- Material: Cobalt
- Cutting Ends: Single
- Geometry: Corner Rounding
- Units: Fractional