Roughing / Hogging End Mills
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill - Multi-Flute * Single End * Coarse Pitch [See More]
- Cutting Ends: Single
- Cutter: 0.250
- Units: Fractional
- Shank: 0.375
from KEO Cutters
Carbide Decimal 2-Flute Single-End Ball Nose Regular [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.055
from SwiftCARB
Strong core for heavier cuts, excellent for high nickel alloys [See More]
- Geometry: Square; Radius (optional feature)
- Units: Fractional; Metric (optional feature)
- Cutting Ends: Single
- Cutter: 0.250 to ?
from Sandvik Coromant Co.
The CoroMill ® 210 is a very productive roughing concept to use when high metal removal rate is the first priority. A 10 ° entering angle allows extreme feed rates when face milling. This directs the cutting forces in an axial direction, which provides a stable cutting action and no... [See More]
- Cutting Ends: Single
- Cutter: 1.000 to 6.000
- Units: Fractional (optional feature); Metric
- Shank: 0.370 to 0.575
from Cutting Edge Technologies, Inc.
Coating: Uncoated. Diameter: 1/4". End Type: Square. Flute Length: 3/4". Flute Length Type: Standard. Number of Flutes: Overall Length: 2 1/2". Shank Diameter: 1/4". Substrate Material: Carbide. Type: End Mill [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Contour360º
4 Flute, 30 Degree Helix, Center Cutting. Solid Carbide End Mills. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . This end mill has a corner radius of 0.5 mm and is AlTiN coated. [See More]
- Cutter: 0.118
- OAL: 1.97
- Shank: 0.118
- Material: Carbide
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. A rough finish is produced which will require a finishing pass. Designed to machine soft materials such as aluminum, plastic, zinc alloys. Wide futes provide rapid chip... [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.188 to 1.000
from Promax Tool Company
3 Flute Ball Rougher-Finisher for Stainless Steel - Series 122. Series 122 3 Flute Ball Rougher-Finisher for Stainless Steel. View Speeds and Feeds page. Features: Designed for aggressive slotting and pocket milling. Best in in low and high carbon steels, stainless steel, titanium and high... [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill - 3-Flute Single End * Stub Length * Fine Pitch * Center Cutting [See More]
- Cutting Ends: Single
- Cutter: 0.250
- Units: Fractional
- Shank: 0.375
from KEO Cutters
Carbide Decimal 2-Flute Single-End Ball Nose Stub [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.055
from Sandvik Coromant Co.
Versatile in the widest sense of the word, CoroMill ® 316 can be applied for high feed face milling, slot milling, helical interpolation, shoulder milling, profile milling and chamfer milling of components in all material groups from ISO P to ISO S. CoroMill ® 316 allows machine shops to... [See More]
- Cutting Ends: Single
- Cutter: 0.375 to 1.000
- Units: Fractional (optional feature); Metric
- Shank: 0.394 to 1.256
from Cutting Edge Technologies, Inc.
Coating: TIN. Diameter: 1/4". End Type: Square. Flute Length: 3/4". Flute Length Type: Standard. Number of Flutes: Overall Length: 2 1/2". Shank Diameter: 1/4". Substrate Material: Carbide. Type: End Mill [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . This end mill has a corner radius of .010 in and is AlTiN coated. [See More]
- Cutter: 0.189
- OAL: 4.00
- Shank: 0.188
- Material: Carbide
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. A rough finish is produced which will require a finishing pass. Used in difficult and abrasive materials and tough alloy materials, such as stainless steel, nickel base... [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.375 to 1.500
from Promax Tool Company
3 Flute Rougher-Finisher for Aluminum - Series 119. Series 119 3 Flute Rougher-Finisher for Aluminum. View Speeds and Feeds page. Features: Designend to improve performance in profiling and pocket rougher-finishing applications. Best in Aluminum and and light alloys. Eccentric relieved for a 25%... [See More]
- Cutting Ends: Single
- Cutter: 0.125
- Units: Fractional
- Shank: 0.125
from Universal Cutting Tools, Inc.
M42 8% Cobalt Roughing End Mill for Aluminum - 3-Flute Single End * Center Cutting * Coarse Pitch [See More]
- Cutting Ends: Single
- Cutter: 0.250
- Units: Fractional
- Shank: 0.375
from KEO Cutters
Carbide Decimal 2-Flute Single-End Regular [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.177
from Sandvik Coromant Co.
CoroMill ® 419 is a high-feed milling concept with five edges for roughing to semi-finishing. It offers excellent performance in many material groups and has great possibilities for optimization. The high-feed and light-cutting action enable a soft sound, creating an operator-friendly... [See More]
- Cutting Ends: Single
- Cutter: 1.250 to 4.000
- Units: Fractional (optional feature); Metric
- Shank: 0.354
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 4.00 in AlTiN coated Solid Carbide end mill. [See More]
- Geometry: Square
- Shank: 0.750
- Cutter: 0.752
- OAL: 4.00
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates then conventional end mills. These tools will plunge cut. A rough finish is produced which will require a finishing pass. Used in diffcult and abrasive materials and tough alloy materials, such as... [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.188 to 1.500
from Promax Tool Company
3 Flute Rougher-Finisher for Stainless Steel - Series 117. Series 117 3 Flute Rougher-Finisher for Stainless Steel. View Speeds and Feeds page. Features: Designed for aggressive slotting and pocket milling. Best in in low and high carbon steels, stainless steel, titanium and high temperature alloys. [See More]
- Cutting Ends: Single
- Cutter: 0.125
- Units: Fractional
- Shank: 0.125
from KEO Cutters
Carbide Decimal 2-Flute Single-End Stub [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.005 to 0.177
from Sandvik Coromant Co.
In our comprehensive range of CoroMill ® Plura mills, you will find the best option for your application, whether you need a tool that is optimized for a specific material or one that performs well in many materials. The range of tools includes high-performance solutions for high-speed... [See More]
- Geometry: Square (optional feature); Ballnose (optional feature); Radius (optional feature)
- Units: Fractional (optional feature); Metric
- Cutting Ends: Single
- Cutter: 0.118 to 0.787
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 50.0 mm TiAlN coated Solid Carbide end mill. [See More]
- Cutter: 0.236
- OAL: 1.97
- Shank: 0.236
- Coating: Coated; Titanium Aluminum Nitride; TiAlN
from Melin Tool Company
Due to the finer sinusoidal form on cutting edge, finer chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which will require finishing pass. Designed to machine soft materials such as aluminum, plastic, zinc alloys. Wide... [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250 to 1.000
from Promax Tool Company
4 Flute Rougher-Finisher for All Material Types - Series 120. Series 120 4 Flute Rougher-Finisher for All Material Types. View Speeds and Feeds page. Features: Bridges the gap between full roughing and finishing applications. Maintains an exceptional part surface finish. Relieves tool pressure... [See More]
- Cutting Ends: Single
- Cutter: 0.125
- Units: Fractional
- Shank: 0.125
from KEO Cutters
Carbide Decimal 4-Flute Single-End Regular [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.040 to 0.100
from Sandvik Coromant Co.
The CoroMill ® 216 end mill is a robust end mill concept for roughing and semi-finishing of curved surfaces in machining centers, CNC milling machines, and copy-milling machines for die and mold, aerospace, automotive, and associated industries. Benefits. Maximum security and reliability. High... [See More]
- Cutting Ends: Single
- Cutter: 0.394 to 1.968
- Units: Fractional (optional feature); Metric
- Edges: Inserts
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 4.625 in Uncoated coated M42 Cobalt end mill. [See More]
- Cutter: 0.626
- OAL: 4.62
- Shank: 0.625
- Coating: Uncoated; Uncoated
from Melin Tool Company
Due to the finer sinusoidal form on cutting edge, finer chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which may require a finishing pass. These tools will plunge cut. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.188 to 1.500
from Promax Tool Company
5 Flute Rougher-Finisher for Steels & High Strength Alloys - Series 121. Series 121 5 Flute Rougher-Finisher for Steels & High Strength Alloys. View Speeds and Feeds page. Features: Bridges the gap between full roughing and finishing applications. Maintains an exceptional part surface finish. [See More]
- Cutting Ends: Single
- Cutter: 0.750
- Units: Fractional
- Shank: 0.750
from KEO Cutters
2 & 4 Flute Single Ball Nose Extra-Long [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125 to 1.000
from Sandvik Coromant Co.
CoroMill ® 300 is a positive round insert concept for a broad range of operations such as face milling, pocketing, and profiling. Light cutting action allows for smooth entries and exits and for vibration-free use of extended tool setups. The positive concept is used for machines with high and... [See More]
- Cutting Ends: Single
- Cutter: 0.375 to 8.000
- Units: Fractional (optional feature); Metric
- Shank: 0.315 to 1.000
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 2.500 in TiCN coated Solid Carbide end mill. [See More]
- Cutter: 0.374
- OAL: 2.50
- Shank: 0.375
- Coating: Coated; Titanium Carbonitride; TiCN
from Melin Tool Company
Due to the finer sinusoidal form on cutting edge, finer chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which may require a finishing pass. These will not plunge cut. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.188 to 2.000
from Promax Tool Company
General Purpose Rougher - Series 100. Series 100 General Purpose Roughing End Mill. View Speeds and Feeds page. Features: Recommened for general purpose applications in material upto 50Rc. Suggested for use in normalized carbon and alloy steels, cast steels, stainless steels, cast irons, brass and... [See More]
- Cutting Ends: Single
- Cutter: 0.188
- Units: Fractional
- Shank: 0.188
from KEO Cutters
2 and 4 Flute Double-End Ball Nose Stub [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Double
- Cutter: 0.031 to 0.750
from Sandvik Coromant Co.
CoroMill ® 600 is a modern innovative milling cutter –a completely new design based on our unique iLock ™ insert clamping solution. Developed for roughing and semi-finishing of turbine blades for power generation, this round-insert cutter enables a new approach to meet the challenges... [See More]
- Cutting Ends: Single
- Cutter: 0.984 to 2.480
- Units: Fractional (optional feature); Metric
- Shank: 0.472
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 2.500 in TiCN coated M42 Cobalt end mill. [See More]
- Cutter: 0.374
- OAL: 2.50
- Shank: 0.375
- Coating: Coated; Titanium Carbonitride; TiCN
from Melin Tool Company
Due to the finer sinusoidal form on cutting edge, finer chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which will require a finishing pass. [See More]
- Geometry: Square
- Units: Metric
- Cutting Ends: Single
- Cutter: 0.236 to 0.984
from Promax Tool Company
Roughers for Hardened Materials - Series 103. Series 103 Roughing End Mill for Hardened Materials. View Speeds and Feeds page. Features: Designed for use on extremely tough to machine materials with a 60+Rc hardness and high temperature alloys. 20 Degree Helix 4 Flute. Corner Radius standard to... [See More]
- Cutting Ends: Single
- Cutter: 0.250
- Units: Fractional
- Shank: 0.250
from KEO Cutters
2 and 4 Flute Double-End Stub [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Double
- Cutter: 0.031 to 0.750
from Reid Supply
Reid Supply has a range of ball end mills, square end mills, corner radius end mills, roughing end mills and more. . 3.00 in TiAlN coated Solid Carbide end mill. [See More]
- Cutting Ends: Single
- OAL: 3.00
- Cutter: 0.375
- Coating: Coated; Titanium Aluminum Nitride; TiAlN
from Melin Tool Company
Can remove material at high roughing speeds while producing finishes close to conventional end mills, due to the chip-breaker form. The 8% cobalt gives high edge hardness at high temperature levels. These end mills are designed to machine soft materials such as aluminum, plastic, zinc alloys. Wide... [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250 to 1.000
from Promax Tool Company
Roughers for Light Alloys - Series 102. Series 102 Roughing End Mill for Light Alloys. View Speeds and Feeds page. Features: Designed for light materials like Aluminum, brass, copper, etc. as well as general purpose applications for deep slots and pockets. Reduces tool pressure and generates less... [See More]
- Cutting Ends: Single
- Cutter: 0.188
- Units: Fractional
- Shank: 0.188
from KEO Cutters
2 and 4 Flute Single-End Ball Nose Long [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125 to 1.000
from Melin Tool Company
Used for radius or contouring part surfaces. Due to the finer sinusoidal form on cutting edge, finer chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which may require a finishing pass. These will not plunge cut. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.188 to 1.250
from Promax Tool Company
Roughers for Space Age Exotic Materials - Series 101. Series 101 Roughing End Mill for Space Age Exotic Materials. View Speeds and Feeds page. Features: Designed Specifically for applications in materials such as titanium and nickel based/high temperature alloys (inconel, rene, wasploy, etc.). [See More]
- Cutting Ends: Single
- Cutter: 0.188
- Units: Fractional
- Shank: 0.188
from KEO Cutters
2 and 4 Flute Single-End Extra-Long [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125 to 1.000
from Melin Tool Company
Used for roughing out “T ” slots. [See More]
- Geometry: T-Slot
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.959 to 2.646
from KEO Cutters
2 and 4 Flute Single-End Long [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125 to 1.000
from Melin Tool Company
Form relieved on high strength carbide for excellent profle milling. Made from premium submicron grain carbide. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250 to 1.000
from KEO Cutters
2 and 4 Flute Single-End Regular [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 1.000
from Melin Tool Company
Can remove material at high roughing speeds while producing finishes close to conventional end mills, due to the chip-breaker form. Made from premium submicron grain carbide. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.250 to 1.000
from KEO Cutters
2 and 4 Flute Single-End Stub [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.750
from Melin Tool Company
A free cutting roughing end mill which will produce a smooth finish. 40 ° helix with eccentric relief. Small corner radius for strength. Made from premium submicron grain carbide. [See More]
- Geometry: Square
- Units: Metric
- Cutting Ends: Single
- Cutter: 0.236 to 0.984
from KEO Cutters
2 & 4 Flute Single End Extra Long Reach [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.100
from Melin Tool Company
Form relieved on high strength carbide for excellent profle milling. Made from premium submicron grain carbide. [See More]
- Geometry: Square
- Units: Metric
- Cutting Ends: Single
- Cutter: 0.236 to 0.984
from KEO Cutters
Corner Radius Carbide 2- & 4-Flute [See More]
- Geometry: Radius
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.125 to 0.500
from Melin Tool Company
Due to the sinusoidal form on cutting edge, small chips are produced which allow faster feed rates than conventional end mills. These tools will plunge cut. A rough finish is produced will require a finishing pass. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.375 to 1.250
from KEO Cutters
2 and 4 Flute Square End and Ball Nose [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.500
from Melin Tool Company
Due to the finer sinusoidal form on cutting edge, fner chips are produced than coarse pitch, which are easier flushed away and reduce re-cutting and packing. A rough finish is produced which may require a finishing pass. These tools will plunge cut. [See More]
- Geometry: Square
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.375 to 1.250
from KEO Cutters
3- and 4-Flute Long Shank [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.016 to 0.250
from KEO Cutters
3-Flute Decimal Extra Long Reach [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.250
from KEO Cutters
3-Flute Extra Long Reach [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.250
from KEO Cutters
3-Flute Extra Reach Stub Ball Nose [See More]
- Geometry: Ballnose
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.094
from KEO Cutters
3-Flute Long Reach [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.250
from KEO Cutters
3-Flute Long Reach Single-End High Performance [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.010 to 0.250
from KEO Cutters
3-Flute Regular Length Extended Reach [See More]
- Geometry: Radius
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.250
from KEO Cutters
3-Flute Stub Length [See More]
- Geometry: Radius
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.250
from KEO Cutters
3-Flute Stub/Long Reach/Long Shank [See More]
- Geometry: Square (optional feature); Ballnose (optional feature)
- Units: Fractional
- Cutting Ends: Single
- Cutter: 0.031 to 0.094