Specialty / Other Wire Rope Fittings and Cable Fittings
from Certex UK
General: Support grip designed to support the cable weight as it hangs vertical or horizontally. Also ideal for taking the strain of connecters and wall sockets. Design primarily for wind turbine use, designs for other applications available on request. Warning: Substantial safety ratios have been... [See More]
- Diameter: 0.3937 to 0.5906
- Application: Power and Public Utility
- Material: Galvanized; Stainless; Stainless steel or galvanised on request.
from Certex UK
General: Stocking which can be opened with two impacted eyes for pulling-in of ropes or cables or check of hose. The grip can be placed anywhere along a cable, rope or hose and after that "sewed" together with a rope which are locked with wire rope clips. On request the eyes can be provided with... [See More]
- Diameter: 0.3937 to 0.7874
- Application: Power and Public Utility
- Material: Galvanized; Steel wire rope - Galvanized.
from Certex UK
General: Open Ended Cablegrip ideal for joining two cables to form a continuous loop. Typical application: replacement of elevator cables, where the old cable would be attached to the new one, and the cable then fed round with ease. Design: Pleated of double wire ropes. [See More]
- Diameter: 0.3937 to 0.7874
- Application: Power and Public Utility
- Material: Galvanized; Steel wire rope - Galvanized.
from Certex UK
The Ropeblock closed spelter socket CSS designed with mechanical values (Charpy-V > 42 joule / - 20 ° C) for though and low temperature use. All sockets have a 100% efficency on the MBL of the steel wire rope but are limited to the MBL of the socket. The CSS sockets are Type Approved by DNV... [See More]
- Diameter: 4.25 to 4.53
- Application: Power and Public Utility
- Material: Steel; Quenched and tempered cast steel.
- Features & Approvals: Socket Fitting
from Certex UK
McKissick Closed spelter socket for steel wire rope ø 8 mm up to ø 102 mm. Spelter socket terminations have an efficiency rating of 100%, based on the catalogue strength of wire rope. Features: Forged Steel Sockets through 38 mm, cast alloy steel 40 mm through 102mm. All cast steel sockets... [See More]
- Diameter: 0.4331 to 0.5118
- Application: Power and Public Utility
- Material: Steel; Forged steel from wire rope ø 8mm up to 38mm. From ø 40mm Cast Alloy steel.
- Features & Approvals: Socket Fitting
from Certex UK
Sockets incorporate a reduced machined area of the shank which is the equivalent to the proper after swage dimension. Before swaging, this provides for an obvious visual difference in the shank diameter. After swaging, a uniform shank diameter is created allowing for a QUIC CHECK ™ permanent... [See More]
- Diameter: 0.2362
- Application: Power and Public Utility
- Material: Steel; Carbon Steel.
- Features & Approvals: Socket Fitting
from Certex UK
At least 25% greater WLL than traditional Grade 8 products. Proof Load tested at 2.5 times the WLL with certification for each batch manufactured. Fatigue rated to 20,000 cycles at 1.5 times the WLL. Suitable for use with both Grade 8 and Grade 10 chain. When fitting G10 components are added to G8... [See More]
- Load: 3086
- Application: Power and Public Utility
- Material: Steel; Quenched and Tempered Alloy Steel.
from Certex UK
End stops for crane rope applications. Features: These end stops are designed for full load applications of rotation resistant and low rotation ropes. The chamfered surface around the cylinder matches different fitting devices. The bore of the end stop is slightly conical to distribute the stress... [See More]
- Type: Stop Sleeve
- Material: Steel; Mild carbon steel.
- Diameter: 0.5118
- Application: Power and Public Utility
from Certex UK
End Stops for crane rope applications. Type ESP has an inspection hole and is prepared for an RFID chip and gives the possibility to check tests and certificates of the product. Featueres:These end stops are designed for full load applications of rotation resistant and low rotation ropes. The... [See More]
- Type: Stop Sleeve
- Material: Steel; Mild carbon steel.
- Diameter: 0.9055
- Application: Power and Public Utility
from Certex UK
Welded Master Link designed for 3-4 legs Wire Rope and Chain Slings. At least 25% greater WLL than traditional Grade 8 products. Proof Load tested at 2.5 times the WLL with certification for each batch manufactured. Fatigue rated to 20,000 cycles at 1.5 times the WLL. [See More]
- Load: 28440
- Application: Power and Public Utility
- Material: Steel; Quenched and Tempered Alloy Steel.
from Certex UK
Welded Master Link designed for 1-2 legs Wire Rope and Chain Slings. At least 25% greater WLL than traditional Grade 8 products. Proof Load tested at 2.5 times the WLL with certification for each batch manufactured. Fatigue rated to 20.000 cycles at 1.5 times the WLL. [See More]
- Load: 25353
- Application: Power and Public Utility
- Material: Steel; Quenched and Tempered Alloy Steel.
from Certex UK
Standard: Certex Standard [See More]
- Type: Eye
- Material: Steel; Steel
- Diameter: 0.4331
- Application: Power and Public Utility
from Certex UK
Forged clevis fittings with bolt, nut and cutterpin for fast connection of steel wire rope. Connector shall be used with non-rotating or cat 1. rotation resistant wire rope only. The connector has to be moulded/casted on the steel wire rope with wirelock resin. [See More]
- Diameter: 0.4331 to 0.5118
- Application: Power and Public Utility
- Material: Steel; Quenched and tempered cast steel.
- Features & Approvals: Socket Fitting
from Certex UK
These ferrules are normally used on stainless steel wire ropes to achieve the best possible resistance against corrosion. Stainless steel Ferrule - recommended for machine pressing only. Suitable for long term use in salt water, waste water treatment and chemical processing. [See More]
- Material: Stainless; Stainless steel, AISI 316.
from Certex UK
Round ferrule (R) is intended to be pressed on single layer round strand wire ropes, for instance on preventer wires or used as end stop. The expected strength regarding this end-termination is approximately 50% of the MBL of the wire rope (informative only). Round aluminium end stops are not... [See More]
- Type: Stop Sleeve
- Material: Aluminum; Aluminum
from Certex UK
Round copper ferrule (RCU) is intended to be pressed on single round strand wire ropes, for instance on preventer wires or used as end stop. Copper as material suits well together with stainless steel wire rope, to avoid galvanic corrosion in saltwater environments. The expected strength regarding... [See More]
- Type: Stop Sleeve
- Material: Bronze / Copper Alloy; Copper (almost 99,9%)
from Certex UK
The turnback ferrule system is easy to use. It is quick, safe and has proved itself to be totally reliable. The ferrules are thoroughly specified and very well defined for many different wire rope applications. The ferrules can be used for fibre core single layer wire ropes, steel core single layer... [See More]
- Material: Aluminum; Aluminum
from Certex UK
The copper ferrule (TCU) is intended for stainless steel wire rope to avoid galvanic corrosion. The pressing of TCU ferrules requires approx 25% higher pressure than the corresponding T ferrule of aluminium alloy. Note: We do not guarantee the strength of slings for lifting activities made of Copper... [See More]
- Material: Bronze / Copper Alloy; Copper (almost 99,9%)
from Certex UK
The turnback ferrule system is easy to use. It is quick, safe and has proved itself to be totally reliable. The ferrules are thoroughly specified and very well defined for many different wire rope applications. The ferrules can be used for fibre core, single layer wire ropes, steel core single layer... [See More]
- Material: Aluminum; Aluminum.
from Certex UK
Standard: Certex Standard [See More]
- Type: Fork / Strap Eye
- Material: Steel; Steel
- Diameter: 0.4331
- Application: Power and Public Utility
from Certex UK
Design: Hook-hook. End fittings are quenched and tempered, bodies heat treated by normalizing. Standard: According to Federal Specifications FF-T-791b. [See More]
- Load: 1499
- Application: Power and Public Utility
- Material: Steel; Steel.
from Certex UK
End fittings are quenched and tempered, bodies heat treated by normalizing. Forged jaw ends are fitted with bolts and nuts for 6 mm through 16 mm, and pins and cotters on 19 mm through 70 mm sizes. Modified UNJ thread on end fittings for improved fatigue properties. Body has UNC threads. Standard:... [See More]
- Load: 794
- Application: Power and Public Utility
- Material: Steel; Steel.
from Certex UK
Standard: Certex Standard [See More]
- Diameter: 0.3937
- Application: Power and Public Utility
- Material: Steel; Steel
from Certex UK
Safety Factor: Standard: Certex Standard [See More]
- Type: Stop Sleeve
- Application: Power and Public Utility
- Material: Steel; Steel
from Certex UK
Pearshaped coupling master link. Can be used with insulated swivel 8-088N. Order Coupling Pin and C-Sleeve Set 8-P015. [See More]
- Load: 27558
- Application: Power and Public Utility
- Material: Steel; Quenched and tempered alloy steel.
from Loos & Co., Inc.
Zinc die cast fittings perform just as well as traditional fittings in most applications. They hold cable breaking strength when properly designed and manufactured. Intricate designs and threads allow for better performance than many more expensive machined parts. By eliminating secondary operations... [See More]
- Type: Ball
- Material: Galvanized; Zinc Alloy, Zamak 5
- Diameter: 0.1560
- Application: Commercial; Aircraft Cable; Mining; Oil & Gas Wells; Rigging, Lashing or other Material Handling; Marine; Elevator; Power and Public Utility; Forestry; Transit; Automotive or Vehicular