Automatic Transfer Control Transfer Switches
from Penncat Corporation
Thomson Technology TS 830 series of Automatic Transfer Switches employ two mechanically interlocked enclosed contact power switching units and a microprocessor based controller to automatically transfer system load to an alternate supply in the event of a utility supply failure. System load is... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 3200
- Style: Wall Mounted
- AC Voltage: 208 to 480
from SOCOMEC
ATyS t and g are three-phase automatic transfer switches, 3 or 4 poles, with positive break indication. They incorporate all the functions offered by the ATyS d, as well as functions intended for mains/mains application (ATyS t) and mains/genset applications (ATyS g). In automatic mode they enable... [See More]
- Switch Control: Automatic Transfer Control
- Current: 125 to 3200
- Style: Wall Mounted
- Number of Poles: 3 to 4
from Kussmaul Electronics Company, Inc.
Automatically Transfers Load from Shore Line Power to Generator Power. 20 Amp Capacity. Indicates Source of Power. Easy Installation. The Auto Interlock II is a power transfer relay which automatically transfers the 120 volt A.C. from the shoreline to the auxiliary generator when the generator is... [See More]
- Switch Control: Automatic Transfer Control
- Current: 20
- Style: Wall Mounted
- AC Voltage: 120
from Specialty Product Technologies
STABILINE Automatic Bus Transfer Switches are designed for hard-wired wall or bulkhead mounting in NEMA 4X enclosures. ABT models automatically transfer from one power source to a second source should the first fail outside of specification. Offered in fast (.5 second) or delayed (3 second) types... [See More]
- Switch Control: Manually; Automatic Transfer Control
- Current: 25 to 600
- Style: Wall Mounted; Bulkhead
- AC Voltage: 440
from Electric Generators Direct
Generator Ready. •Makes a home ready for a home standby generator. Designed For Outdoor Installation. •NEMA 3R Aluminum cabinet can be surface mounted & padlocked. Ovation Series 200-Amp Automatic Transfer Switch. •Microprocessor-controlled and open transition. •Circuit... [See More]
- Switch Control: Automatic Transfer Control
- Power: 50000
- Current: 200
- Number of Poles: 2
from Eaton | Power Quality
The Eaton Pulsar STS is an affordable solution for customers who want to add power redundancy to small networking equipment like switches and routers. This source transfer switch powers them from two different sources (typically the main power and a UPS, or 2 UPSs). Should one power source fail the... [See More]
- Switch Control: Automatic Transfer Control
- Current: 12
- Style: Rack Mounted
- AC Voltage: 120
from LTI Power Systems, Inc.
The LTI static switch will provide virtually uninterruptible. power to any critical load by automatically or manually. selecting between one of two AC input sources. If the. preferred source deviates outside preset limits, the unit. will instantaneously transfer to the secondary source. Upon return... [See More]
- Switch Control: Automatic Transfer Control
- Current: 20 to 50
- Style: Rack Mounted
- AC Voltage: 110 to 240
from Eaton Corporation - Sensors
Breaker Based Automatic Transfer Switches offer an enhanced set of features that will meet your application requirements, and allow for optimal control and improved flexibility for applications requiring continuity of power during the transfer and routine test. In the event of a primary power source... [See More]
- Switch Control: Automatic Transfer Control
- Current: 30 to 1000
- Style: Wall Mounted
- AC Voltage: 600
from Kohler Power Systems
Meet the brains behind your generator system. The ATS is always monitoring your power, making sure you never go without. [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 400
- Style: Wall Mounted
- Phase : Single Phase; Three Phase
from Caterpillar Electric Power
Cat ® transfer switches are designed for a variety of standby power applications. They provide flexibility, reliability and value in a compact package. The open transition power case switch-based Automatic Transfer Switch (ATS) will provide fully functioning transfer in applications where a... [See More]
- Switch Control: Automatic Transfer Control
- Current: 200 to 5000
- Style: Ground Mounted
- AC Voltage: 120 to 600
from Penncat Corporation
Thomson Technology TS 840 series of Automatic Transfer Switches employ two mechanically interlocked enclosed contact power switching units and a microprocessor based controller to automatically transfer system load to a generator supply in the event of a utility supply failure. System load is... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 800
- Style: Wall Mounted
- AC Voltage: 240
from SOCOMEC
ATyS p are three-phase automatic transfer switches, 3 or 4 poles, with positive break indication. They incorporate all the functions offered by the ATyS t and g, as well as functions designed for power management and communication. In automatic mode they enable the monitoring of, and the on load... [See More]
- Switch Control: Automatic Transfer Control
- Current: 125 to 3200
- Style: Wall Mounted
- Number of Poles: 3 to 4
from Kussmaul Electronics Company, Inc.
Automatically Transfers Load from Shore Line Power to Generator Power. 20 Amp Capacity. Indicates Source of Power. No Wiring Needed. Easy Installation. The Auto Interlock III is a power transfer relay which automatically transfers the 120 volt A.C. from the shoreline to the auxiliary generator when... [See More]
- Switch Control: Automatic Transfer Control
- Current: 15
- Style: Wall Mounted
- AC Voltage: 120
from Electric Generators Direct
100-A Indoor Automatic Transfer Switch w/ 10-Circuit Load Center. •Perfect for backing up emergency circuits. Steel NEMA-1 Indoor Enclosure. •Electrostatically applied and baked powder paint. Breakers: •3 x 15A (120V) 1-Pole. •3 x 20A (120V) 1-Pole. •1 x 20A (240V)... [See More]
- Switch Control: Automatic Transfer Control
- Power: 24000
- Current: 100
- Number of Poles: 2
from Eaton Corporation - Sensors
A critical component of any emergency power system, Eaton's contactor based automatic transfer switch quickly and safely shifts the load circuit from a normal power source to the emergency source, permitting critical loads to continue running with minimal or no outage in momentary losses of power. [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 1200
- Style: Wall Mounted
- AC Voltage: 600
from Kohler Power Systems
Safe, dependable protection for critical facilities. 30 to 4000 amps, in standard-, programmed- and closed-transition configurations. Simple, integrated communication interface using Ethernet or LAN line. Service-entrance, non-automatic, automatic and bypass configurations. UL 1008 Listed, CSA and... [See More]
- Switch Control: Automatic Transfer Control
- Current: 30 to 4000
- Style: Wall Mounted
- AC Voltage: 208 to 600
from Caterpillar Electric Power
Cat transfer switches are designed for a variety of standby power applications. They provide flexibility, reliability and value in a compact package. A Bypass Isolation Automatic Transfer Switch (ATS) provides fully functioning transfer in applications where emergency power to critical loads must be... [See More]
- Switch Control: Automatic Transfer Control
- Current: 200 to 5000
- Style: Ground Mounted
- AC Voltage: 120 to 600
from Penncat Corporation
Thomson Technology TS 870 Standard Automatic Transfer Switches employ two mechanically interlocked power switching units with a microprocessor based controller to automatically start a generator and transfer system load to a generator supply in the event of a utility supply failure. System load is... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 1200
- Style: Wall Mounted
- AC Voltage: 208 to 600
from SOCOMEC
ATyS p M are single-phase or three-phase automatic transfer switches with positive break indication. Functions include ATyS t M and ATyS g M capability, with additional programmable parameters and a triggering function. A product model with communication is available. They are intended for use in... [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 160
- Style: Wall Mounted
- AC Voltage: 160 to 305
from Electric Generators Direct
100-A Indoor Automatic Transfer Switch w/ 12-Circuit Load Center. •Perfect for backing up emergency circuits. Steel NEMA-1 Indoor Enclosure. •Electrostatically applied and baked powder paint. Breakers: •5 x 15A (120V) 1-Pole. •3 x 20A (120V) 1-Pole. •1 x 30A (240V)... [See More]
- Switch Control: Automatic Transfer Control
- Power: 24000
- Current: 100
- Number of Poles: 2
from Eaton Corporation - Sensors
Eaton ’s Automatic Transfer Switch with Bypass Isolation is designed to provide unmatched performance, reliability and versatility for critical standby power applications. The switches can be equipped with the ATC-300 or ATC-800 controllers to match your application needs. A Bypass Isolation... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 1200
- Style: Ground Mounted
- AC Voltage: 600
from Caterpillar Electric Power
Cat ® Service Entrance Rated (SER) automatic transfer switches (ATS) are designed to provide standby power emergency power to entire installation loads to protect against utility power interruption; yet allow the ATS to be as close as possible to the point of service entrance. By safely and in... [See More]
- Switch Control: Automatic Transfer Control
- Current: 30 to 5000
- Style: Wall Mounted
- AC Voltage: 120 to 600
from Penncat Corporation
Since its introduction, GE ’s Zenith ZTS Series of transfer switches has become a hallmark of quality and performance. Reliability resulting from superior design and heavy duty construction has made the ZTS the industry standard for critical installations. Our emphasis on research and... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 4000
- Style: Ground Mounted
- Number of Poles: 2 to 4
from SOCOMEC
ATyS t M and ATyS g M are three-phase (4P) automatic transfer switches with positive break indication. The ATyS g M is also available in 2P for single phase applications. The ATyS t M and ATyS g M both include ATyS d M functionality together, with an integrated controller for automatic transfer... [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 160
- Style: Wall Mounted
- AC Voltage: 176 to 288
from Electric Generators Direct
100-A Indoor Automatic Transfer Switch w/ 14-Circuit Load Center. •Perfect for backing up emergency circuits. Steel NEMA-1 Indoor Enclosure. •Electrostatically applied and baked powder paint. Breakers: •4 x 15A (120V) 1-Pole. •6 x 20A (120V) 1-Pole. •1 x 20A (240V)... [See More]
- Switch Control: Automatic Transfer Control
- Power: 24000
- Current: 100
- Number of Poles: 2
from Eaton Corporation - Sensors
The Magnum family of transfer switches offers the highest withstand capacity in the industry. Designed for applications where total system coordination must be accomplished, they offer a variety of standby power applications for critical and non-critical loads. During normal power interruption,... [See More]
- Switch Control: Automatic Transfer Control
- Current: 200 to 5000
- Style: Wall Mounted
- AC Voltage: 600
from Caterpillar Electric Power
The Cat ® CTE Series transfer switches are configurable for applications requiring the dependability and ease of operation found in a full featured power contactor type transfer switch. The CTE Series is equipped with the MX350 controller that is designed for the most demanding transfer or... [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 4000
- Style: Ground Mounted
- AC Voltage: ? to 600
from Penncat Corporation
GE ’s Zenith ZTG Series switches are built for standard applications requiring the dependability and ease of operation found in a power contactor switch. ZTG switches are equipped with GE ’s Zenith MX150 microprocessor panel, which controls the operation and displays the status of the... [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 3000
- Style: Wall Mounted
- AC Voltage: 120 to 575
from SOCOMEC
ATyS non-automatic transfer switches are designed for use in total system optional standby applications for the safe transfer between a normal and an alternate power source. The changeover is done in open transition and with minimum supply interruption during transfer ensuring full compliance with... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 400
- Style: Wall Mounted
- AC Voltage: 240 to 600
from Electric Generators Direct
100-A Indoor Automatic Transfer Switch w/ 16-Circuit Load Center. •Perfect for backing up emergency circuits. Steel NEMA-1 Indoor Enclosure. •Electrostatically applied and baked powder paint. Breakers: •5 x 15A (120V) 1-Pole. •5 x 20A (120V) 1-Pole. •1 x 20A (240V)... [See More]
- Switch Control: Automatic Transfer Control
- Power: 24000
- Current: 100
- Number of Poles: 2
from Eaton Corporation - Sensors
The Magnum series automatic transfer switch with bypass isolation is designed to excel in applications where total system coordination must be accomplished while achieving a high level of withstand, interrupting, and closing performance. Service, inspection, and testing may be performed while... [See More]
- Switch Control: Automatic Transfer Control
- Current: 200 to 5000
- Style: Wall Mounted
- Actuator Type: Toggle
from Caterpillar Electric Power
Caterpillar offers one of the broadest ranges of transfer switch products in the marketplace and incorporates a solutions-based approach for CSA/UL/IEC listed applications. Cat ® ATS products offer differentiated features that simplify installation, operation, and system integration; yet are... [See More]
- Switch Control: Automatic Transfer Control
- Current: 40 to 3000
- Style: Wall Mounted
- AC Voltage: 600
from SOCOMEC
Applications. Automatic Transfer System, 16A, 19" rack mounted. Permanent back-up for mission-critical, IT and telecommunications equipment within the INTERNET server field. Advantages. • Dual power supply for redundancy : based on a double power supply system, ASYS monitors voltage quality and... [See More]
- Switch Control: Automatic Transfer Control
- Current: 16
- Style: Rack Mounted
- AC Voltage: 120 to 240
from Electric Generators Direct
Three Devices in One. •Load shedding device, load center and automatic transfer switch. Built-In Load Shedding. •Allows you to safely alternate two high-wattage appliances. •Alternate two central air conditioners without overloading. 16-Circuit Priority Load Center. •Drops... [See More]
- Switch Control: Automatic Transfer Control
- Number of Poles: 2
- Current: 200
- Phase : Single Phase
from Caterpillar Electric Power
Cat ® transfer switches are designed for a variety of standby power applications. They provide flexibility, reliability and value in a compact package. A Bypass Isolation Automatic Transfer Switch (ATS) provides fully functioning transfer in applications where emergency power to critical loads... [See More]
- Switch Control: Automatic Transfer Control
- Current: 100 to 1200
- Style: Ground Mounted
- AC Voltage: 120 to 600
from SOCOMEC
Applications. Permanent back-up for mission-critical, IT and telecommunications equipment within the internet server field. Advantages Dual power supply for redundancy. Based on a double power supply system, the IT SWITCH monitors voltage quality and automatically transfers the load from the... [See More]
- Switch Control: Automatic Transfer Control
- Current: 16 to 20
- Style: Rack Mounted
- AC Voltage: 100 to 240
from Electric Generators Direct
Nexus ™ Automatic Transfer Switch. Compatible With Generac Nexus ™ or Generac R200 Controllers. •Leverages digital load management (DLM) technology. •Ability to manage 2 A/C units with no additional hardware. •Intelligently manage 4 more loads w/ additional DLM modules. [See More]
- Switch Control: Automatic Transfer Control
- Power: 24000
- Current: 100
- Number of Poles: 2
from Caterpillar Electric Power
Caterpillar offers standard paralleling solutions, which are ideal for use in Distributed system configurations found in Data Center applications as well as Soft Load Automatic Transfer Switch (ATS) applications. The Emergency Transfer Load Manager (EXL) product line provides standard paralleling... [See More]
- Switch Control: Automatic Transfer Control
- Features: CSA Certification; UL Listed
- Style: Wall Mounted