Coating: None Cutting Tool Inserts
from Sandvik Coromant Co.
Auto AF insert for milling [See More]
- Coating: None
- Thickness: 0.500
- Application: Milling
- Radius: 0.071
from Allied Machine & Engineering Corp.
Original T-A ® is an excellent choice for general purpose use. The design provides fast penetration rates that produce good hole size and finish. Standard geometry combines highly efficient and stable cutting action to minimize power consumption. Recommended for use in most steels, cast irons,... [See More]
- Coating: None
- Shape: Spade Drill
- Application: Drilling
- Material: Cobalt
from Greenleaf Corporation
35 ° diamond chip control insert, precision finishing config [See More]
- Coating: None
- Shape: Diamond; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 35°
from Sandvik Coromant Co.
Auto FS insert for milling [See More]
- Coating: None
- Thickness: 0.188
- Application: Milling
- Radius: 0.020
from Allied Machine & Engineering Corp.
GEN3SYS ® Drill Inserts and Holders penetrate up to 35% faster than competitive drilling products. Allied's AM200 ® coating increases tool life up to 50% when compared tocompetitor's premium coatings. [See More]
- Coating: None
- Shape: Spade Drill
- Application: Drilling
- Material: C1 AM200®
from Greenleaf Corporation
35 ° diamond insert, flat top config [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 35°
from Sandvik Coromant Co.
Auto FS insert for milling [See More]
- Coating: None
- Thickness: 0.188
- Application: Milling
- Radius: 0.020
from Allied Machine & Engineering Corp.
T-A ® Flat Bottom Drill Inserts are made of either Super Cobalt or Carbide substrates as follows: Series Y through 2.5 are available in Super Cobalt and Carbide, while series 3 & 4, offered in range:1.353" (34,36mm) to 2.570" (65,28mm), are only available in Super Cobalt. The Super Cobalt base... [See More]
- Coating: None
- Shape: Spade Drill
- Application: Drilling
- Material: Cobalt
from Greenleaf Corporation
35 ° diamond insert, screw on configuration [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 35°
from Sandvik Coromant Co.
Auto Roughing insert for milling [See More]
- Coating: None
- Thickness: 0.188
- Application: Milling
- Chamfer Angle: 45
from Allied Machine & Engineering Corp.
GEN2 T-A ® drill inserts provide lower drilling forces, increased drill stability, smoother breakout on through-hole and allows for improved chip formation. These inserts feature AMEC's exclusive AM200 ® coating for increased tool life. [See More]
- Coating: None
- Shape: Spade Drill
- Application: Drilling
- Material: Cobalt
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: V-Bottom
- Application: Milling
- Tip Angle: 35°
from Sandvik Coromant Co.
Auto Roughing insert for milling [See More]
- Coating: None
- Thickness: 0.188
- Application: Milling
- Chamfer Angle: 45
from Allied Machine & Engineering Corp.
Allied'sAccuPort 432 ® Port Contour Cutters are produced to strict manufacturing tolerances. This provides the customer with the assurance that the forms produced are within the finish tolerances of each specification. [See More]
- Coating: None
- Shape: Circular
- Application: Drilling
- Quantity: 1
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: Diamond
- Application: Milling
- Tip Angle: 35°
from Sandvik Coromant Co.
Auto T-Line insert for milling [See More]
- Coating: None
- Thickness: 0.375
- Application: Milling
- Radius: 0.031
from Allied Machine & Engineering Corp.
- Coating: None; Titanium Nitride; Titanium CarboNitride; Titanium Aluminum Nitride; AM200 / AM210
- Shape: Rectangular
- Application: Threading
- Thickness: 0.080
from Greenleaf Corporation
55 degree diamond insert, precision finishing config [See More]
- Coating: None
- Shape: Diamond; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 55°
from Sandvik Coromant Co.
Auto T-Line insert for milling [See More]
- Coating: None
- Thickness: 0.375
- Application: Milling
- Chamfer Angle: 90
from Greenleaf Corporation
Negative geometry, screw on configuration [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 55°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for grooving [See More]
- Coating: None
- Thickness: 0.161
- Application: Grooving
- Radius: 0.004
from Greenleaf Corporation
Negative geometry, no hole [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 55°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for grooving [See More]
- Coating: None
- Thickness: 0.169
- Application: Grooving
- Radius: 0.008
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: V-Bottom
- Application: Milling
- Tip Angle: 35°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for grooving [See More]
- Coating: None
- Thickness: 0.169
- Application: Grooving
- Radius: 0.008
from Greenleaf Corporation
Negative diamond insert, screw on configuration [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for grooving [See More]
- Coating: None
- Thickness: 0.169
- Application: Grooving
- Radius: 0.008
from Greenleaf Corporation
Negative diamond insert, no hole [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for grooving [See More]
- Coating: None
- Thickness: 0.278
- Application: Grooving
- Radius: 0.031
from Greenleaf Corporation
80 degree diamond insert, precision finishing config [See More]
- Coating: None
- Shape: Diamond; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for parting [See More]
- Coating: None
- Thickness: 0.161
- Application: Parting
- Radius: 0.008
from Greenleaf Corporation
Positive diamond geometry, no hole configuration [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for parting [See More]
- Coating: None
- Thickness: 0.169
- Application: Parting
- Radius: 0.059
from Greenleaf Corporation
Positive flat top configuration, no hole [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for parting [See More]
- Coating: None
- Thickness: 0.169
- Application: Parting
- Radius: 0.012
from Greenleaf Corporation
Negative diamond insert, rough stuff configuration [See More]
- Coating: None
- Shape: Diamond; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for parting [See More]
- Coating: None
- Thickness: 0.169
- Application: Parting
- Radius: 0.004
from Greenleaf Corporation
80 ° trigon chip control configuration, screw on [See More]
- Coating: None
- Shape: Trigon; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for profiling [See More]
- Coating: None
- Radius: 0.039
- Application: Profiling
- Material: Aluminium/Non-ferrous
from Greenleaf Corporation
80 ° trigon finishing configuration [See More]
- Coating: None
- Shape: Trigon; Chipbreaker
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for profiling [See More]
- Coating: None
- Thickness: 0.169
- Application: Profiling
- Radius: 0.059
from Greenleaf Corporation
80 ° trigon flat top config [See More]
- Coating: None
- Shape: Trigon
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for profiling [See More]
- Coating: None
- Thickness: 0.169
- Application: Profiling
- Radius: 0.059
from Greenleaf Corporation
55 degree diamond insert, flat top config [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 55°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for profiling [See More]
- Coating: None
- Thickness: 0.169
- Application: Profiling
- Radius: 0.079
from Greenleaf Corporation
80 degree diamond insert, flat top config [See More]
- Coating: None
- Shape: Diamond
- Application: Milling; Turning
- Tip Angle: 80°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for profiling [See More]
- Coating: None
- Thickness: 0.171
- Application: Profiling
- Radius: 0.118
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: Groove/Turn Shape
- Application: Boring; Turning
- Tip Angle: 90°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for turning [See More]
- Coating: None
- Thickness: 0.169
- Application: Turning
- Radius: 0.012
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: Groover Shape
- Application: Boring; Grooving; Turning
- Tip Angle: 90°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for turning [See More]
- Coating: None
- Thickness: 0.169
- Application: Turning
- Radius: 0.012
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute. [See More]
- Coating: None
- Shape: Groove/Turn Shape
- Application: Boring; Turning
- Tip Angle: 90°
from Sandvik Coromant Co.
CoroCut ® 1-2 insert for turning [See More]
- Coating: None
- Thickness: 0.171
- Application: Turning
- Radius: 0.016
from Greenleaf Corporation
Groover shape, no hole configuration [See More]
- Coating: None
- Shape: Groover Shape
- Application: Boring; Grooving; Turning
- Tip Angle: 90°
from Sandvik Coromant Co.
CoroCut ® Q insert for parting [See More]
- Coating: None
- Thickness: 0.122
- Application: Parting
- Radius: 0.004
from Greenleaf Corporation
A complete API ring groove tooling solution. Finish API ring grooves in Inconel 625 clad overlay in less than a minute [See More]
- Coating: None
- Shape: Groover Shape
- Application: Boring; Grooving; Turning
- Tip Angle: 90°