Film Drying / Air Setting Marine Coatings
from FORREST Technical Coatings
FirmFoot ® Slip Resistant EpoxyEpoxy Skid Resistant Floor Paint. Pre-mixed epoxy paint with grit to eliminate slippery spots on stairs, walkways, ramps, boat decks, diving boards and dozens of other common locations! Offers firm footing under wet conditions. Easy to use, no mixing. Meets VOC... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Concrete; Metallic; Plastic; Steel; Wood; Other; Fiberglass
- Type: Paint; Clear Coat
- Coating Material: Epoxy; Resin
from FORREST Technical Coatings
A high solids, 3.5 VOC or lower phenolic modified alkyd primer with non-lifting properties. Rust-inhibitive pigments protect against corrosion. Appropriate for use on interior or exterior steel substrates and compatible with alkyd, acrylic, vinyl, epoxy or urethane top coats. A 2.8 VOC version... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Steel
- Type: Coating; Paint; Primer; Base Coat
- Coating Material: Alkyd; Formaldehyde Resins (Phenolic, Furan, Melamine); Resin; Solvent
from Whitford Corporation
High temperature resistant; low coefficient of friction; abrasion/wear resistant; easy clean; dry film lubricant; thermoset; wide use temperature; anti-galling. [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Ceramic; Metallic; Plastic; Wood
- Type: Coating
- Coating Material: Solvent
from Dampney Company, Inc.
Elastoid 1300 is a single-package, high-build, elastomeric coating and vapor barrier. It is formulated from multiphase synthetic rubber copolymers which interact to provide an unusual range of desirable chemical and physical properties. It is tough, flexible, and corrosion-resistant and provides... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Concrete; Metallic; Steel
- Type: Coating
- Coating Material: Rubber
from Heresite Protective Coatings, LLC
This family of thin film, air dry phenolics is excellent for resistance to corrosive fume atmospheres and is particularly good in marine and salt air environments. VR-514 coatings exhibit superior durability, excellent adhesion and good flexibility. Typical applications include Swimming Pools, Waste... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Metallic; Steel
- Type: Coating
- Coating Material: Formaldehyde Resins (Phenolic, Furan, Melamine); Resin
from Redwood Plastics
Wearlon Super F-4 is the hardest in the line of Wearlon coatings, improving abrasion resistance and prolonging the life of your propeller. It is a water based, environmentally friendly coating that can be painted or sprayed on. Wearlon Super F-4 is a non-stick foul release coating that minimizes... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum
- Type: Coating; Non-Stick Foul Release
- Coating Material: Water
from Sherwin-Williams Protective & Marine Coatings
ArmorSeal ®REXTHANE I FLOOR COATING is a high solids, single component, aliphatic, moisture cure urethane, VOC complying, moisture resistant industrial floor coating. This urethane coating cures to a high gloss and chemical resistant film equivalent to two-part urethane coatings. Impact and... [See More]
- Cure / Setting Technology: Film Drying; Reactive or Moisture Cured
- Substrate: Concrete; Steel; Wood; Other; Metalizing, Steel with Zinc
- Type: Coating; Clear Coat
- Coating Material: Polyurethane; Resin; Aliphatic
from Sherwin-Williams
Sherwin-Williams is a global provider of protective and marine coatings, offering a complete line of high performance coatings technologies to combat corrosion. We deliver unmatched service and coatings specification support to meet our customers ’ coatings needs. [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Plastic; Wood
- Type: Coating
- Coating Material: Epoxy; Fluoropolymers; Formaldehyde Resins (Phenolic, Furan, Melamine); Resin
from Columbia Chemical Corporation
Lac-Chro-SEAL ® is a non-hazardous lacquer coating for enhanced corrosion resistance on electroplated deposits and base metals. It air dries quickly to a very thin, clear & glossy finish which prevents fingerprints and provides significant protection to high humidity conditions. [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Other; Zinc & Zinc Alloy Deposits Over Steel
- Type: Coating; Clear Coat; Sealer; Lacquer
- Coating Material: Acrylic; Zinc; Water
from Aervoe Industries Incorporated
Prolongs battery life, won't crack, chip, or peel, dries quickly [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Other; Connections, Battery, Cable Terminals
- Type: Coating; Sealer
- Coating Material: Acrylic; Alkyd; Resin; Solvent
from Dampney Company, Inc.
A water-borne copolymer that is designed for application to rusted ferrous metal surfaces. When properly applied the coating converts the rusted surface to a dark, stable organic iron compound. This product has a low permeability factor and is impermeable to oxygen and moisture while providing a... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Steel
- Type: Coating; Rust Conversion
- Coating Material: Resin; Copolymer
from Sherwin-Williams Protective & Marine Coatings
ACROLON ™ 7300 is a high-solids, low film-build acrylic polyurethane coating that is used as a durable finish coat over high-performance anti-corrosion systems. This tin-free and silica-free aliphatic polyurethane has excellent resistance to atmospheric exposures and maintains gloss and color,... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Steel
- Type: Coating
- Coating Material: Acrylic; Polyurethane; Resin
from Columbia Chemical Corporation
Zinc-Chro-SHIELD ® is a unique sealer for chromated zinc deposits which dramatically increases corrosion protection at very little additional cost. And since it's added to the final stagnant rinse at low concentrations (1% to 8% by volume), no additional equipment is required. Zinc-Chro-SHIELD... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Steel; Other; Zinc & Zinc Alloy Deposits Over Steel
- Type: Coating; Sealer
- Coating Material: Zinc; Water; Silicate Based
from Dampney Company, Inc.
Endcor 772 protects steel surfaces subjected to immersion in fresh or salt water, exposure in tidal or splash zones, or burial in soil. It is effective on the interiors of tanks and lines containing brine, crude oil, petroleum products, sewage or strong alkalies. It is resistant to a wide range of... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Steel
- Type: Coating; Clear Coat
- Coating Material: Epoxy; Resin
from Sherwin-Williams Protective & Marine Coatings
COPPER BOTTOM ANTI-FOULING PAINT #45 is a semihard, anti-fouling developed for the shallow draft trade. It offers a moderately high concentration loading of cuprous oxide and a chemically modified binder that only slightly dissolves upon immersion service. RECOMMENDED USAGE. Used for moderate... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Steel; Wood; Other; Iron, Galvanized
- Type: Paint
- Coating Material: Metal Filled; Cuprous Oxide
from Sherwin-Williams Protective & Marine Coatings
DTM ACRYLIC COATING is a 100% acrylic, water reducible, corrosion resistant coating for light to moderate industrial use. Designed for new construction or maintenance use and can be used directly over prepared substrates. Chemical resistant. Corrosion resistant. Fast dry. Low odor. Flash rust/early... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Concrete; Steel; Wood; Other; Galvanizing, Drywall, Zinc Rich Primers
- Type: Coating
- Coating Material: Acrylic; Resin; Water
from Sherwin-Williams Protective & Marine Coatings
Dura-Plate ® 154 EPOXY SPLASH ZONE COATING is a high solids, high build amine epoxy coating that will withstand extreme conditions of abrasion and corrosion. It can be applied from 10 to 40 mils dry in one coat. This can be applied by brush over prepared, damp substrates while providing adequate... [See More]
- Cure / Setting Technology: Film Drying; Thermoset
- Substrate: Concrete; Steel; Other; Iron
- Type: Coating
- Coating Material: Epoxy; Resin; Amine
from Sherwin-Williams Protective & Marine Coatings
Dura-Plate ® 235 Multi-Purpose Epoxy is a modified epoxy phenalkamine, formulated specifically for immersion and atmospheric service in marine and industrial environments. Dura- Plate 235 provides exceptional performance in corrosive environment, and can be applied at temperatures as low as 0... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Concrete; Steel; Other; Iron
- Type: Coating; Self-Priming
- Coating Material: Epoxy; Resin; Phenalkamine
from Sherwin-Williams Protective & Marine Coatings
Epolon ™ II RUST INHIBITIVE EPOXY PRIMER is a high performance, exterior/interior, VOC compliant, lead and chromate free, high solids, two component, rust inhibitive, catalyzed polyamide epoxy steel primer. Specifically engineered for corrosion protection and chemical and weather resistant... [See More]
- Cure / Setting Technology: Film Drying; Multicomponent
- Substrate: Steel; Other; Iron
- Type: Coating; Primer
- Coating Material: Epoxy; Resin; Catalyzed Polyamide
from Sherwin-Williams Protective & Marine Coatings
Fast Clad ® HB Acrylic is a one component, fast dry, high build finish designed for one coat application directly to organic or inorganic zinc-rich primers or other recommended primers. May also be applied directly to prepared steel. High film build in one coat. Superior gloss and color... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Aluminum; Concrete; Steel; Wood; Other; Zinc Rich Primers, Drywall
- Type: Coating
- Coating Material: Acrylic; Resin
from Sherwin-Williams Protective & Marine Coatings
HI-MIL Sher-Tar ® EPOXY is a high build, polyamide cured, epoxy coal tar coating, which can be applied at high film thickness in one coat. RECOMMENDED USAGE. For use over prepared substrates such as steel and concrete in industrial environments. Penstocks. Liner for clarifiers. Dam gates. [See More]
- Cure / Setting Technology: Film Drying; Thermoset
- Substrate: Aluminum; Concrete; Steel; Other; Iron, Galvanizing
- Type: Coating
- Coating Material: Epoxy; Resin; Coal Tar
from Sherwin-Williams Protective & Marine Coatings
HI-SOLIDS ALKYD METAL PRIMER is a fast drying, high solids, low VOC, rust inhibitive, alkyd primer for steel surfaces, and is free of heavy metal hazards. It is easy to apply by spray and has good resistance to general atmospheric weathering. It can be topcoated with alkyd and latex coatings. Fast... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Metallic; Steel; Other; Iron
- Type: Coating; Primer
- Coating Material: Alkyd; Resin
from Sherwin-Williams Protective & Marine Coatings
SherPlate PW Epoxy. SherPlate PW Epoxy is an edge retentive, ultra high solids epoxyamine coating engineered for immersion service in potable water pipes and storage tanks. The rapid return to service and high build, edge retentive properties of this coating provide superior protection. One or two... [See More]
- Cure / Setting Technology: Film Drying
- Substrate: Concrete; Metallic; Steel
- Type: Coating
- Coating Material: Epoxy; Resin