Steel, Hardened and Ground Industrial Pins
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Length: 0.1250
from Fairlane Products, Inc.
These positive locking quick release pins have a wide range of applications in fastening, locating, and alignment applications. The pins will not release until the button on the handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or... [See More]
- Material: Stainless; HardenedSteel; 4130 steel, 300 stainless, or 17-4 stainless
- Design Units: English; Metric
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 0.7500
from SPIROL
The Coiled Spring Pin was invented by SPIROL in 1948. SPIROL offers Coiled Pins in three duties, light, standard and heavy, to provide a variety of combinations of strength, flexibility and diameter to accommodate different host materials and applications. Standard duty (sometimes called... [See More]
- Material: Stainless; HardenedSteel; UnhardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Coiled Spring Pins
- Design Units: Metric
from National Bolt & Nut Corporation
DOWEL PINS. Because dowel pins provide precise alignment of fastened components, they are commonly used as shelf supports in furniture or as supports for hanging items such as key rings, tools, toilet roll dispensers and picture frames. Constructed from heat treated alloy steel, National Bolt &... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel (optional feature); OversizeDowel (optional feature)
- Nominal Diameter: 0.0625 to 1
from PennEngineering®
PEM ® self-clinching studs are installed by placing them in properly sized holes in the sheets and squeezing into place with any standard press. The squeezing action embeds the head of the stud into the sheet. The metal displaced by the head flows smoothly and evenly around the ribs and into the... [See More]
- Material: HardenedSteel
- Design Units: Metric
- Pin Type: Groove; Self-Clinching Pins - Type FH, FHS, FHA - Metric
- Nominal Diameter: 0.1181
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0610
- Pin Type: Groove
- Length: 0.3750
from Fairlane Products, Inc.
These positive locking quick release pins have a wide range of applications in fastening, locating, and alignment applications. The pins will not release until the button on the handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or... [See More]
- Material: Stainless; HardenedSteel; 4130 steel, 300 stainless, or 17-4 stainless
- Design Units: English; Metric
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 0.7500
from SPIROL
Dowel bushings are used to locate components in conjunction with bolts which pass through the inside of the bushing after it has been installed. Separate holes for locating pins are eliminated. The hardened bushings also absorb shear loads, isolating the bolts from these forces. [See More]
- Material: HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: StraightDowel; Dowel Bushing
- Design Units: English
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0620
- Pin Type: NonthreadedTaper
- Length: 0.4380
from Fairlane Products, Inc.
These positive locking quick release pins have a wide range of uses in fastening, locating, and alignment applications. The pins will not release until the button on the handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or removed... [See More]
- Material: Stainless; HardenedSteel; 4130 steel, 300 stainless, or 17-4 stainless
- Design Units: English; Metric
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 0.6250
from SPIROL
Dowel bushings are used to locate components in conjunction with bolts which pass through the inside of the bushing after it has been installed. Separate holes for locating pins are eliminated. The hardened bushings also absorb shear loads, isolating the bolts from these forces. [See More]
- Material: HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: StraightDowel; Dowel Bushing
- Design Units: Metric
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0625
- Pin Type: Roll
- Length: 0.1880
from Fairlane Products, Inc.
These positive locking quick release pins have a wide range of applications in fastening, locating, and alignment applications. The pins will not release until the button on the handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or... [See More]
- Material: Stainless; HardenedSteel; 4130 steel, 300 stainless, or 17-4 stainless
- Design Units: English; Metric
- Pin Type: QuickRelease; L-Pin
- Nominal Diameter: 0.1875 to 0.7500
from SPIROL
Design-in SPIROL ’s Series GD100 Ground Hollow Dowels for Precision Alignment and Substantial Cost Savings. SPIROL Ground Hollow Dowels are designed to be direct replacements for standard Ground Solid Dowels per ISO 8734. They are used where centerline tolerancing and precision alignment are... [See More]
- Material: HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: StraightDowel; Ground Hollow Dowel
- Design Units: Metric
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Length: 0.1880
- Nominal Diameter: 0.0627
from Fairlane Products, Inc.
These positive locking quick release pins have a wide range of applications in fastening, locating, and alignment applications. The pins will not release until the button on the handle is depressed. Once the button is depressed, the balls retract into the shank allowing the pin to be inserted or... [See More]
- Material: Stainless; HardenedSteel; 4130 steel, 300 stainless, or 17-4 stainless
- Design Units: English; Metric
- Pin Type: QuickRelease; T-Pin
- Nominal Diameter: 0.1875 to 0.7500
from SPIROL
Slotted Spring Pins are headless hollow cylindrical tubes having a longitudinal slot down the entire length with chamfered or round ends to aid installation. For automation assembly and high performance applications, SPIROL recommends Coiled Spring Pins for error free installation. [See More]
- Material: Stainless; HardenedSteel; UnhardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Roll
- Design Units: English
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Length: 0.3937
- Nominal Diameter: 0.0591
from SPIROL
Slotted Spring Pins are headless hollow cylindrical tubes having a longitudinal slot down the entire length with chamfered or round ends to aid installation. For automation assembly and high performance applications, SPIROL recommends Coiled Spring Pins for error free installation. [See More]
- Material: Stainless; HardenedSteel; UnhardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Roll
- Design Units: Metric
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0591
- Pin Type: Roll
- Length: 0.3937
from SPIROL
Slotted Spring Pins are headless hollow cylindrical tubes having a longitudinal slot down the entire length with chamfered or round ends to aid installation. For automation assembly and high performance applications, SPIROL recommends Coiled Spring Pins for error free installation. [See More]
- Material: Stainless; HardenedSteel; UnhardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Roll
- Design Units: Metric
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0320
- Pin Type: Hitch
- Length: 0.4688
from SPIROL
One of the advantages of partnering with SPIROL early in the design stage is that if one of our 30,000 standard items doesn ’t meet your specific application requirements, the solution is often a simple derivation of our standard design. Regardless of the complexity, SPIROL ’s Engineers... [See More]
- Material: Aluminum; Brass; Stainless; HardenedSteel; UnhardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Custom Pins
- Design Units: English
from Stock Drive Products & Sterling Instrument - SDP/SI
Industrial fasteners are hardware devices that join two or more items together, creating a semi-permanent or permanent connection. The fasteners most frequently used by machinery designers are screws, nuts, retaining rings, and various types of pins because of the basic role that they play in the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.0420
- Pin Type: Hitch
- Length: 1
from SPIROL
Spring alignment dowels are used to accurately locate components with respect to each other. They are formed around arbors to assure roundness. It is recommended that one half the hole tolerance be used for the fixed location of the dowel and one half for the hole in the mating part. [See More]
- Material: HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: StraightDowel; Spring Alignment Bushing
- Design Units: English
from SPIROL
Spring alignment dowels are used to accurately locate components with respect to each other. They are formed around arbors to assure roundness. It is recommended that one half the hole tolerance be used for the fixed location of the dowel and one half for the hole in the mating part. [See More]
- Material: HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: StraightDowel; Spring Alignment Bushing
- Design Units: Metric
from SPIROL
Coiled Spring Pins are shock-absorbing fastening elements that provide flexibility, uniform strength, equal stress distribution, closer diameter tolerances, no interlocking, trouble-free automatic feeding, and they reduce costs. Heavy, standard, and light duty coiled spring pins provide combinations... [See More]
- Material: Stainless; HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: CoiledSpring; Coiled Spring Pins
- Design Units: English; Metric
from SPIROL
Slotted Spring Pins are headless hollow cylindrical tubes having a longitudinal slot down the entire length with chamfered or round ends to aid installation. [See More]
- Material: Stainless; HardenedSteel
- Bulk/Assorted Package: Bulk
- Pin Type: Roll; Slotted Spring Pins
- Design Units: English; Metric
from TFC Ltd.
Type SCH pins provide a strong flush head assembly in material as thin as 1.0mm (.040in.) with high torque-out and push-out performance. Material: SCH - Carbon steel, heat-treated. SCHN - Carbon steel, Non heat-treated. SCHS - 300 Series Stainless steel. SCHA - 2024T4 Aluminium. Finish: SCH - Zinc... [See More]
- Material: HardenedSteel
- Pin Type: Clinch
from SelfLube, Inc.
SelfLube Sleeve Ejectors have forged heads for maximum strength and are supplied heat treated, ground. Nitrided and polished to reduce friction and wear. [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: Ejector
- Nominal Diameter: 0.1870 to 1
from W.M. Berg
DOWEL [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.0627
from Hartford Technologies, Inc.
Detent pins refer to pins that have a mechanical feature that prevents motion until this feature is released. One simple example is a pin that has a spring loaded ball pressed into a hole along its length. The pin cannot be disassembled until the ball is pressed into the body of the pin, allowing... [See More]
- Material: Stainless; HardenedSteel; Bearing grade chrome steel
- Nominal Diameter: 0.0310 to 1
- Pin Type: Detent
- Length: 0.1250 to 3
from Carr Lane Manufacturing Co.
These Ball Lock Pins have an adjustable grip length. They can be used for clamping, or simply to provide a variable grip length. The threaded handle turns to provide a +/- 1/4" clamping range or adjustment range. When used just for variable grip length (not for clamping), the handle can be secured... [See More]
- Material: Stainless (optional feature); HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: QuickRelease
- Nominal Diameter: 0.2500 to 1
from NBS Corp.
How do you measure precision? Two-thousandths of an inch at a time. From 3/4 ” to 1/16 ” diameter, NBS carries one of the largest selections of dowel pins in the entire United States. Featuring a tolerance less than .0002 inches, a chamfered end and an exclusive mirror polish finish,... [See More]
- Material: HardenedSteel; AISI 4135
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.0630
from Pivot Point, Inc.
These basic rings are a low cost alternative to Split Key Rings and are often used as ring-grips in various applications, including pins such as Detent Ring Pins. Available in either hard drawn wire with an attractive zinc plated finish or corrosion resistant stainless steel. Other Rings and Cotters... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: CircleCotter
- Design Units: English
from Monroe Engineering
Material. Steel-Hardened, Black Oxide finish. Stainless-303 Type, Bright Finish. Accurate Locating, Positioning Device. Simple installation. Lock Nut Supplied. Threaded Control End Allows Actuation by Linkage to Remote Operation, Hydraulics, etc. [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: Indexing / Pop
- Nominal Diameter: 0.2000
from DME Company
D-M-E Metric Angle Pins, constructed of DIN 1.7131 (AISI 5115 type) steel, can be used as angle (cam) pins or as straight leader pins. [See More]
- Material: HardenedSteel
- Design Units: Metric
- Pin Type: StraightDowel
- Nominal Diameter: 0.3937 to 1.97
from SelfLube, Inc.
Available in a variety of sizes. [See More]
- Material: HardenedSteel
- Design Units: Metric
- Pin Type: Ejector
- Nominal Diameter: 0.1575 to 0.6299
from Hartford Technologies, Inc.
Dowel pins, when inserted into receiving holes, are used to join and precisely align parts of an assembly. Dowel pins may also be used as location pins. These pins are common in the automotive and aerospace industries as well as in manufacturing furniture. Size Ranges. Diameter: .031 ″ to... [See More]
- Material: Stainless; HardenedSteel; UnhardenedSteel
- Nominal Diameter: 0.0310 to 1
- Pin Type: StraightDowel
- Length: 0.1250 to 3
from Carr Lane Manufacturing Co.
Precision alignment pin with a ground shank. This popular single-acting type is positive locking until released by pushing the button, which moves the center spindle forward to allow the locking balls to retract into a radial groove. This type has the widest range of types and sizes. Available in... [See More]
- Material: Stainless (optional feature); HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 1
from Pivot Point, Inc.
Invented by Pivot Point, the popular Bow-Tie Locking Cotter ™ works like a Hair Pin Cotter, but locks itself on! Push or pull the cotter leg into the mating hole, the Bow-Tie snaps into a zero-tension locked position. It is easily released by lifting the loop and sliding the cotter off. The... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: a.k.a. Hitch Pin Clip
- Design Units: English
from Monroe Engineering
Material: Knob Black Technopolymer. Steel-Hardened Black Oxide Finish. Stainless-303 Type Bright Finish. Accurate Locating, Positioning Device. Simple Installation. Locking Nut Supplied. Allows Pin to be held in the Withdrawn Position [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: Indexing / Pop
- Nominal Diameter: 0.2000
from DME Company
Precision made of superior quality hotwork die steel (standard hardness 30-35 HRC). Heads are hot-forged for uniform grain flow, higher tensile strength, then annealed to permit easier machining and stamping. +.0008"/+.0003" tolerance on pin diameter ensures a close fit for coring purposes. Pin body... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.0937 to 0.7500
from SelfLube, Inc.
Made in a variety of sizes. Material is 1.2344 (H-13) with a core: 50-52 Rc; Surface: 65-70 Rc. [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: Ejector
- Nominal Diameter: 0.0310 to 1
from Hartford Technologies, Inc.
Hartford Technologies custom manufactures precision knurled pins and knurled studs that provide the highest levels of straightness, roundness, and hardness, without marks. Hartford knurled pins and knurled studs are manufactured in high volumes in straight, diamond and helical styles, tapered and... [See More]
- Material: Stainless; HardenedSteel; Chrome Steel
- Nominal Diameter: 0.3750
- Pin Type: Knurled
- Length: 3
from Carr Lane Manufacturing Co.
Precision locating pin often used with the mating bushing shown here to align two pieces of a fixture. The pin's head and shank diameters are concentric to within .0005" TIR. The bushing's ID and OD are concentric to within .0003" TIR. [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: Bullet-nose
- Nominal Diameter: 0.2500 to 0.5000
from Pivot Point, Inc.
This cotter is wound or turned on from the middle out. Start by threading the open wire end inside the circle into the hole on shaft or pin. Keep turning the ring until it snaps into place. To remove, start turning the circle again in the same direction and it comes right off. Very secure fasteners,... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: CircleCotter
- Design Units: English
from Monroe Engineering
Material: Knob-Black Technopolymer. Steel-Hardened, Black Oxide Finish. Stainless-303 Type, Bright Finish. Accurate Locating, Positioning Device. Simple Installation. Locking Nut Supplied. Pin in Always Returned to Extended Position [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: Indexing / Pop
- Nominal Diameter: 0.2000
from DME Company
Precision made of superior quality hotwork die steel (high hardness 50-55 HRC). Heads are hot-forged for uniform grain flow, higher tensile strength, then annealed to permit easier machining and stamping. +.0008"/+.0003" tolerance on pin diameter ensures a close fit for coring purposes. Pin body and... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.0937 to 0.7500
from SelfLube, Inc.
Available in a variety of sizes. The hardness of this particular pin is 58-62 Rc. [See More]
- Material: HardenedSteel
- Design Units: Metric
- Pin Type: Ejector
- Nominal Diameter: 0.0394 to 0.7874
from Carr Lane Manufacturing Co.
Bullet-nose round pins and diamond pins are often used together (with the mating bushings shown here) to align two pieces of a fixture. Diamond pins are relieved, to locate only in 1 axis. The pin's shank diameter and the bushing's OD are the same size, to allow boring the installation hole in both... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: Bullet-nose
- Nominal Diameter: 0.2500 to 1
from Pivot Point, Inc.
Pivot Point manufactures Clevis Pins in-house. Clevis Pins may also be called Hitch Pins, Cold Headed Pins, Headed Pins or Cold Formed Pins. Wide stock selection and highly customizable - Standard Clevis Pins are made from low carbon steel and stocked plain finish. Additional plating finishes are... [See More]
- Material: HardenedSteel; Plain Finish
- Bulk/Assorted Package: Assortment
- Pin Type: Clevis
- Design Units: English
from Monroe Engineering
Material - SAE - 1117 Steel Carburized and Hardened to C-58-62. Tapped Hole is Soft. O.D. Ground to +.0003 +.0001. Leading End has 10 ° Taper. Opposite, Tapped End, has Radius [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel; PullDowel
- Nominal Diameter: 0.2500
from DME Company
Guide Pins with Collar [See More]
- Material: HardenedSteel
- Design Units: Metric
- Pin Type: StraightDowel
- Nominal Diameter: 0.7087 to 0.9449
from Carr Lane Manufacturing Co.
Similar to a standard Jig Pin, except that the pin body is positively retained in a locking bushing. In fully retracted position, the bushing's spring clip snaps into the pin's groove. This holds the pin fully retracted by spring force and positively prevents removal. Spring pressure also holds the... [See More]
- Material: HardenedSteel
- Nominal Diameter: 0.1875 to 0.5000
from Pivot Point, Inc.
A double loop adds flexibility for a wider fit range. Stresses are evenly spread throughout the loop, giving longer life and more repeatability. High quality part made of hard drawn wire and zinc plated. Pivot Point also offers standard Hair Pin Cotters, also known as Hair Pins, Hair Pin Clips,... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: a.k.a. Hitch Pin Clip
- Design Units: English
from DME Company
The D-M-E Guided Ejection System, when properly installed, holds the ejector assembly in alignment and supports the weight of the ejector assembly throughout the entire machine cycle. This greatly reduces wear on ejection components and prevents possible cocking of the ejector plates. It is... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.7490 to 1.5
from Carr Lane Manufacturing Co.
Threaded alignment pin usually used for clamping. The bushing must be welded in place at the proper position to suit the application [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: T-Pin
- Nominal Diameter: 0.1930 to 0.5000
from Pivot Point, Inc.
Hair Pin Cotters are a spring-type cotter made to be reusable. Hair Pin Cotters are generally meant to be used in through-holes while Hair Pin Clips are generally meant to be used on a groove. Double Loop Hair Pin Cotters are also available. For more secure cotter pin options, try our Bow-Tie... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: a.k.a. Hitch Pin Clip
- Design Units: English
from DME Company
Precision made of superior quality, thermal, shock-resisting hotwork die steel. Hot-forged heads provide uniform grain flow, higher tensile strength. Outside diameter nitrided to 65-74 HRC hardness and finished to minimize wear. Heads annealed for easy machining. Centerless ground and polished outer... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.2500 to 0.3750
from Carr Lane Manufacturing Co.
Medium-accuracy tapered locating pin used with the mating bushing shown here. Compensates for considerable misalignment. Can be used for quick assembly of two fixture pieces. [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: ConeLocator
- Nominal Diameter: 0.7500 to 1
from Pivot Point, Inc.
Kickout Cotter Rings are a type of Circle Cotter with a "kick-out" design that is made for speed and economy. Easily removable, this cotter can be installed fast by inserting the "kick-out" end into hole on pin or shaft and winding it through until it snaps into place. To remove, just start winding... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: CircleCotter
- Design Units: English
from DME Company
Reduces cycle times. Ten times better conductivity than steel. Moldstar 150 (C18000) beryllium-free copper-based alloy. Hardness of 90-98 Rockwell B. Available in 21 diameters and four lengths [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.0937 to 0.7500
from Carr Lane Manufacturing Co.
Solid alignment pin with a ground shank and solid shoulder to hold exact grip-length tolerance. Locking balls hold the pin in place by spring force (not positive locking like a Ball Lock Pin). Simply push to insert, and pull to remove. Available in steel or stainless steel. [See More]
- Material: Stainless (optional feature); HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 1
from Pivot Point, Inc.
Pivot Point imports this high quality fastener direct - no middlemen. Made to rigid standards, this is the highest quality standard lynch pin available. Made from low carbon steel, zinc plated and yellow chromate dipped, this pin is especially corrosion resistant. Ring is made from hard drawn wire. [See More]
- Material: HardenedSteel; Zinc with Yellow Chromate
- Bulk/Assorted Package: Assortment
- Pin Type: Linch
- Design Units: English
from DME Company
D-M-E Shoulder Guide Pins are hardened and precision ground. Available in-stock in lengths ranging from 1-3/4" to 11-3/4", D-M-E Straight Guide Pins undergo rigorous quality assurance and control measures to provide the consistency and reliability that have made D-M-E the hallmark of mold technology... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.7490 to 1.25
from Carr Lane Manufacturing Co.
Similar to a single-acting Ball Lock Pin, except the center spindle has two grooves instead of one, to release the balls by either pushing or pulling. Pushing on the handle releases the balls and inserts the pin in one motion. Pulling on the handle releases the balls and removes the pin in one... [See More]
- Material: Stainless (optional feature); HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: QuickRelease
- Nominal Diameter: 0.1875 to 1
from Pivot Point, Inc.
Pivot Point imports this high quality fastener direct - no middlemen. Made to rigid standards, this is the highest quality standard lynch pin available. Made from low carbon steel, zinc plated and yellow chromate dipped, this pin is especially corrosion resistant. Ring is made from hard drawn wire. [See More]
- Material: HardenedSteel; Zinc Plated Pin with Clear Chromate (Bright)
- Bulk/Assorted Package: Assortment
- Pin Type: Linch
- Design Units: English
from DME Company
Shoulder Leader Pin [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.4850 to 0.9850
from Carr Lane Manufacturing Co.
Locating pin that provides precise location in one axis while allowing considerable float in the perpendicular axis. Usually used together with a Round Pin, to locate from two holes in a workpiece. Tapered tip for easy part loading. Floating pins are functionally similar to Diamond Pins, except they... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: FloatingLocating
- Nominal Diameter: 0.2500 to 0.6250
from Pivot Point, Inc.
Pull Pins are also known as spring plungers or hand retractable spring plungers. The Pull Pin body is threaded into the application, with ring on outside surface. Pull the ring to retract spring-loaded tip and allow adjustments. Release ring to lock Pull Pin tip into desired hole location. Chamfered... [See More]
- Material: HardenedSteel; Zinc Plated
- Design Units: English
- Bulk/Assorted Package: Assortment
from DME Company
Mold Parts for 34R, 45R, 56N, 58N, 56U, 58U and 68SH Mold Assemblies [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 1 to 4
from Carr Lane Manufacturing Co.
Jig Pins are removable locating pins, precision ground for accurately aligning holes. Similar to an L or T Pin, but with a shoulder to keep the handle raised, and with pin diameter ground .0003" under nominal size. To convert from a T handle to an L handle, slide the roll-pin handle by tapping it... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: T-Pin
- Nominal Diameter: 0.1875 to 0.5000
from Pivot Point, Inc.
Our Original Design!. Pivot Point originally invented Rue Ring ™ Locking Cotter Pins. Don't be fooled by imitations! Our original proven design and manufacturing specifications ensure proper fit and function. The popular and revolutionary Rue Ring ™ Locking Cotter Pin surrounds the shaft... [See More]
- Material: HardenedSteel; Zinc Plated
- Design Units: English
- Bulk/Assorted Package: Assortment
- Nominal Diameter: 0.3200 to 0.3300
from DME Company
D-M-E Straight Guide Pins are hardened and precision ground. Available in-stock in lengths ranging from 1-3/4" to 18-3/4", D-M-E Straight Guide Pins undergo rigorous quality assurance and control measures to provide the consistency and reliability that have made D-M-E the hallmark of mold technology... [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.7490 to 1.5
from Carr Lane Manufacturing Co.
L Pins are removable locating pins, precision ground for accurately aligning holes. The pin is inset into the handle and silver soldered to create a sturdy assembly. The handle is drilled for attaching a cable. [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: L-Pin
- Nominal Diameter: 0.1250 to 0.7500
from Pivot Point, Inc.
Our Original Design!. Pivot Point originally invented Rue Ring ™ Locking Cotter Pins. Don't be fooled by imitations! Our original proven design and manufacturing specifications ensure proper fit and function. The popular and revolutionary Rue Ring ™ Locking Cotter Pin surrounds the shaft... [See More]
- Material: HardenedSteel; Zinc Plated
- Design Units: English
- Bulk/Assorted Package: Assortment
- Nominal Diameter: 0.5100 to 0.5200
from DME Company
MUD Quick-Change Components. Straight Leader Pins [See More]
- Material: HardenedSteel
- Design Units: English
- Pin Type: StraightDowel
- Nominal Diameter: 0.6100 to 0.8530
from Carr Lane Manufacturing Co.
A single-acting ball lock pin with a solid, one-piece body and four balls for high tension loads. Positive locking until released by pushing the button. Sturdy forged shackle for heavy lifting. [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: QuickRelease; Lifting Pin
- Nominal Diameter: 0.2500 to 1
from Pivot Point, Inc.
Pivot Point Split Key Rings are made of high quality, nickel plated steel and designed to lay flat. Special wire drawn to a half circle shape is wound with the flat surfaces together. Construction is a full two turns with a "dog leg" jog where the ends meet. This design offers a smooth appearance... [See More]
- Material: HardenedSteel; Nickel Plated
- Bulk/Assorted Package: Assortment
- Pin Type: CircleCotter
- Design Units: English
from Carr Lane Manufacturing Co.
Similar to a standard Clamping Pin, except that the pin body is positively retained in a locking bushing. In fully retracted position, the bushing's spring clip snaps into the pin's groove. This holds the pin fully retracted by spring force and positively prevents removal. Spring pressure also holds... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: Clamping
- Nominal Diameter: 0.2500 to 0.5000
from Pivot Point, Inc.
Just like a Wire Lock Pin, this fastener is like having a pin and cotter in one secure assembly. Tab Lock Pins are even easier to use than standard wire lock pins! Tab Lock Pins are similar to a Wire Lock Pin but feature a formed "tab" to allow for easy removal. Pull up on tab to remove, push down... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Bulk
- Pin Type: Wire Lock / Snapper / Safety Spring Pin
- Design Units: English
from Carr Lane Manufacturing Co.
Similar to a standard L Pin, except that the pin body is positively retained in a locking bushing. In fully retracted position, the bushing's spring clip snaps into the pin's groove. This holds the pin fully retracted by spring force and positively prevents removal. Spring pressure also holds the... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: L-Pin
- Nominal Diameter: 0.1875 to 0.5000
from Pivot Point, Inc.
Just like a Wire Lock Pin, this fastener is like having a pin and cotter in one secure assembly. Tab Lock Pins are even easier to use than standard wire lock pins! Tab Lock Pins are similar to a Wire Lock Pin but feature a formed "tab" to allow for easy removal. Pull up on tab to remove, push down... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Bulk
- Pin Type: Wire Lock / Snapper / Safety Spring Pin
- Design Units: English
from Carr Lane Manufacturing Co.
Similar to a standard L PIn, except that the pin body is positively retained in a locking bushing. In fully retracted position, the bushing's spring clip snaps into the pin's groove. This holds the pin fully retracted by spring force and positively prevents removal. Spring pressure also holds the... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: T-Pin
- Nominal Diameter: 0.1875 to 0.5000
from Pivot Point, Inc.
Wire lock pins are like having pin and cotter in one secure assembly! The wire loop is pulled over the end of the pin to lock it in place or remove it. As a one- piece fastener, Wire Lock Pins eliminate cotter pin loss and fit most quick release applications. Steel Lanyards or Nylon Lanyards may be... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: Wire Lock / Snapper / Safety Spring Pin
- Design Units: English
from Carr Lane Manufacturing Co.
Precision locating pins with a large shoulder to resist downward forces. Tapered tip for easy part loading. The type shown here, with a slip-fit shank and lockscrew slot, is designed for renewable installation (also available in a press-fit type for permanent installation). Round Pins and Diamond... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: DiamondLocating
- Nominal Diameter: 0.3125 to 1
from Pivot Point, Inc.
Wire lock pins are like having pin and cotter in one secure assembly! The wire loop is pulled over the end of the pin to lock it in place or remove it. As a one- piece fastener, Wire Lock Pins eliminate cotter pin loss and fit most quick release applications. Steel Lanyards or Nylon Lanyards may be... [See More]
- Material: HardenedSteel; Zinc Plated
- Bulk/Assorted Package: Assortment
- Pin Type: Wire Lock / Snapper / Safety Spring Pin
- Design Units: English
from Carr Lane Manufacturing Co.
Precision locating pins with a tapered tip for easy part loading, and a shoulder to resist downward forces (superior to standard dowel pins). Round Pins and Diamond Pins are often used together to locate from two holes in a workpiece. Diamond pins are relieved, to locate only in 1 axis. Round Pins... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: DiamondLocating
- Nominal Diameter: 0.2500 to 1
from Carr Lane Manufacturing Co.
Precision locating pins with a large shoulder to resist downward forces. Tapered tip for easy part loading. The type shown here, with a press-fit shank, is designed for permanent installation (also available in a lockscrew type, with a slip-fit shank for renewable installation). Round Pins and... [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: DiamondLocating
- Nominal Diameter: 0.3125 to 1
from Carr Lane Manufacturing Co.
Removable locating pin with a straight handle, precision ground for accurately aligning holes. The pin is inset into the handle and silver soldered to create a sturdy assembly. The handle is drilled for attaching a cable. [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: RoundLocating
- Nominal Diameter: 0.2500 to 0.5000
from Carr Lane Manufacturing Co.
T Pins are removable locating pins, precision ground for accurately aligning holes. The pin is inset into the handle and silver soldered to create a sturdy assembly. The handle is drilled for attaching a cable. [See More]
- Material: HardenedSteel
- Design Units: English (optional feature); Metric (optional feature)
- Pin Type: T-Pin
- Nominal Diameter: 0.1250 to 0.7500